04/21/2017

BUCKET RIGS FOR SALE

GUS PECH 42  (Ref#965R) 

Manufactured 1976, gas on deck, mounted on 1982 Ford 800 truck with gas engine, 42” turntable, 78’ kelly with bucket, 22” bucket, needs new cable  Price:  $30,000  PRICE REDUCED:  $19,500


BUCKET RIG PACKAGE (Ref #4008R):

- (1) Calweld 150A, 42” ring gear, 1974 Dodge truck, gas/gas

- (1) Earthdrill 36, 3 scope 25’ Kelly, 1985 Ford single axle, gas/gas

- (4) 36” buckets, (1) 24” bucket, (1) 18” bucket, (1) 12” bucket, (1) 36” auger

Price: $50,000 PRICE REDUCED: $40,000


EZ-BORE 120-42  (Ref#1965N) 

Manufactured 1982, Rebuilt 2008. 
Powered by Cummins 6BTA with very low hrs
Drivetrain for the rig is powered by a 6 month old Allison 5 speed transmission.
     All new shafts and drive line to rotary table.
     All new shafts and bearings for rotary table reduction box.
     New pinion gear. Also one spare.
     New factory built 42" rotary table.
     4 new factory built outriggers. One new factory built derrick raising cylinder.
     The other derrick raising cylinder newly rebuilt. 
     All new crown with new shaft and bearings.
     Derrick is 50% new 1/4 wall steel.
     Hinge pin through A-legs is new.
     New pinion shaft, gears, seals and pillow block bearings for draw works.
     Rebuilt side pullout and derrick pushout arms. Pushout arm cylinder newly rebuilt.
     New, oversized helpers platform.
     Lots of enclosed, lockable storage. Also enclosed baskets.
     2 new 6' long tool boxes.
     All new hydraulic and air hoses on the rig.
     New hydraulic oil cooler. 
     Plenty of room for a 250 welder and bottle holders
     Kelly is 3 or 4 stage with a 4" inner bar. All new plates inside kellys.
     Removable insert in bushings to add 4th kelly stage.
     3 stage will drill to 110ft.. 4 stage will drill to 145 ft..
     Bushings and rig are set up with kelly pulldown.
     New 1" kelly line.
     New 5/8" Pullout arm line.
     New 3/4" 2nd line.
     New Miller Swivel on the kelly line.
     55' clearance from crown to the ground.
Mounted on 1999 Mack RD6. Mack 400 hp. engine. 65,000 miles. 264" wheelbase, 4 axle truck. One front, three rear. Like new interior. Heat and A/C. Bosch Wide Ride seats. 13 speed transmission.
Price:  $245,000   PRICE REDUCED:  $150,000
Miscellaneous buckets, tools, augers, stems available at extra cost


EZ BORE 90-52  (Ref#5130Re)  Manufactured 1982, Detroit diesel deck engine, mounted on 1977 Ford truck with diesel engine, triple kelly, 78’ depth  Price:  $115,000


EZ BORE 90-52  (Ref#5130Rd)  Manufactured 1980, Chrysler gas engine, mounted on 1980 International truck with gas engne, triple kelly, 70’ depth  Price:  $105,000


EZ BORE 90-42 BUCKET RIG  (Ref#12597R

Manufactured 1978, 42” ring gear, rebuilt Detroit 453 diesel engine, mounted on 1978 Ford LT800 with Cat 3208 diesel engine, 3 x 7m kelly bar, located Mexico  Price:  $75,000


CALWELD 200B  (Ref#5130Rc)  Manufactured 1974, Ford 300 gas engine, mounted on 1974 Ford F600 truck with gas engine, 70’ depth, 52” diameter, located Mexico  Price:  $85,000


CALWELD 150B BUCKET RIG  (Ref#5130Rb)  Manufactured 1973, Ford gas deck engine, 36” diameter, mounted on 1973 Ford F600 truck, triple kelly bar, 70’ depth, located Mexico  Price:  $50,000


CALWELD 175B  (Ref#10328Ra

42” ring gear, 90’ drill depth, mounted on 1995 Freightliner with sleeper, 60 Series Detroit diesel, 15 speed transmission, 4 outriggers, Calweld 75 ring gear rebuilt recently, 353 Detroit deck engine (rebuilt recently), hoist with 14” Dodge clutch, well maintained and ready to drill  Price:  $95,000 PRICE REDUCED: $65,000


CALWELD 150  (Ref#8922R

36” ring gear, triple scope kelly, (approx. 65’ drill depth), Continental 6 cylinder gas engine, mounted on Chevy C60 truck with 6 cyl gas engine  Price:  $19,500


EZ BORE 90-45 BUCKET RIG (Ref#13642R)

ez bore

Manufactured 1980, 453 Detroit deck engine, mounted on 1979 GMC with 6V71 Detroit engine, Allison auto transmission, hydraulic pull-out arm, break push-out dump, hydraulic crowds, approx 75’ depth capacity, (3) 25’ kelly bars, (1) 26” bucket, (1) 16” bucket, 1 front & 2 rear outriggers, good condition Price:  $145,000 PRICE REDUCED: $105,000


CALDWELD 175 DRILL RIG  (REF#11064R)

Caldweld 175 Drill Rig


42” ring gear, 75’ kelly bar, American 70B hoist, Chrysler 32 industrial gas deck engine, mounted on crane carrier style truck with CAT 3208 engine, 28” digging bucket, has not drilled in 3 years but in good operating condition when parked
PRICE:  $25,000


5200 EARTHDRILL (SIMILAR DESIGN TO CALWELD 250)  (Ref#9097R)

 

PARTS RIG, INCLUDES:

52" ring gear, Model 120B American hoist, Crowd cylinders, bushing and yoke, 3 derrick cylinders, 46' derrick with 4 sheaves (Top 8' derrick unbolts and comes off), all chain guards, hoist covers, rotary clutch new, dump arm cylinders and sheaves valve section (9 spool), dump arm mounting bracket, no dump arm, no engine, no Outriggers, No Kelly, spare chains, sprockets and bearings

PRICE:  $25,000 PRICE REDUCED: $19,500


EARTHDRILL 36M  (Ref#12678Rb) 

Manufactured 1968, Unmounted, 45” ring gear, 3 scope 25’ kelly bar (3” inner), 75’ drill depth, hydraulic dump arm, back dump/push out in derrick, crowd, 6 cylinder International gas deck motor with 4 speed transmission, 4 hydraulic outriggers  Price:  $39,000


EARTHDRILL M36 BUCKET RIG  (Ref#5130Ra)  Manufactured 1973, Ford gas deck engine, mounted on 1969 Ford truck, located Mexico  Price:  $30,000


EARTHDRILL LH45  (Ref#9272N

 

Manufactured 1977, mounted on 1993 Mack truck, Stauffer transmission,  85’ 4-1/4” Kelly, 24” core barrel, 24” bucket, 4-1/4” inner Kelly, 10” outer Kelly, 85’ drill depth, 466 Industrial deck engine, many extra parts, excellent shape 

Price:  $160,000  PRICE REDUCED:  $55,000


CALWELD BUCKET RIG  (Ref#9225Ra) 

 

Similar to 150 but more torque, 42” ring gear, 75’ Kelly bar, hydraulic hoist, hydraulic rotary, hydraulic dump arm, mounted on GMC tandem axle truck, PTO drive with Cat 3208 diesel engine  Price:  $50,000 PRICE REDUCED: $40,000


CALWELD 150 DRILL RIG PACKAGE (Ref#12465N

36” ring gear, mounted on truck with 350 Chevy gas engine, 66’ Kelly bar, 6 cylinder Chrysler deck engine.

Also includes the following extra accessories:

(1) Tower, (1) 36” ring gear, (1) 44’ Kelly bar, (1) 10’ extension, (1) yoke, (1) pulling arm, (1) winch, (2) 3’ buckets, (1) 30” bucket, (1) 18” bucket, (1) 24” bucket, (1) 3’ core bucket, (1) 2’ core bucket, (1) 1’ core bucket and extensions for 4’ – 7’ diameter holes  Price:  $22,500


CALWELD 150  (Ref#15488) 

Manufactured 1970, 292 Chevy 6 cylinder gas engine on deck, mechanical side dumping arm, mounted on single axle 1970 Chevy with 366 Chevy engine, 14’ wheelbase for difficult to access areas, 2 hydraulic outriggers, 42” diameter, 69’ – 72’ drill depth, complete with 24”, 30” and 36” buckets   Price:  $32,500 


CALWELD 150 BUCKET RIG  (Ref#13476N) 

42” ring gear, 2 piece kelly, 40’ length, 6 cylinder Chevy gas deck engine, mounted on Chevy truck  Price:  $14,500


GUS PECH BORING MACHINE  (Ref#1251N

Mounted on 1996 International truck, new paint, 36” ring gear, 24” bucket and bell, complete, ready to go  Price:  $42,500


GUS PECH (Ref#8399N)

Manufactured 1973, gas deck engine, mounted on 1978 GMC with gas engine

Available as package with 1984 Ford pipe truck, diesel engine  Package Price $27,000 REDUCED: $19,500


GUS PECH SUPER 32 BUCKET RIG  (ref#2881

Mounted on 1974 Dodge truck, runs daily  Price:  $25,000 PRICE REDUCED: $12,000