Last Updated: 12/05/2024 2:33 PM
DREDGES FOR SALE
24” CUTTERHEAD SUCTION DREDGE (Ref#3908)
Built 2005, reconditioned 2009 and again in 2015, modular design of all welded steel, 133’ x 32’ x 7’ depth, 3.5’ draft (hull only), 170’ overall length, 24 x 24 HHD 62 Georgia Iron Works pump, DC motor G.E. 500 rpm, 3500 HP continuous 700 VDC armature, 9600 DC Digital drive system rated 3500 hp, 600 VAC input, 60 HZ, 72’ ladder plus 20’ extension, 700 hp electric over hydraulic cutterhead, 300 hp jet pump, 36” x 50’ (plus 40’ extensions) spuds hoisted by independent winch with 200 hp AC vector motors, (2) winches with 200 hp AC vector motors with 150,000# pull at 80 fpm. Ladder hoist independent winch powered with 100 hp AC motor. Dredge takes 4160 volt AC power through 3000’ of 8000 volt rated cable spooled on a diesel driven barge mounted reel. Cat 3406 emergency generator set to operate the winches in case of power failure. Price: $3,500,000
ELLICOTT SERIES 2070 DRAGON 20” X 20” HYDRAULIC CUTTER SUCTION DREDGE (Ref#4062)
20” suction pipe, 20” discharge pipe, 50’ depth, 110’10” L (with ladder raised), 72” hull length x 26’6”W x 7’6” hull depth, 3 pontoons, 4.5’ hull draft (not including spuds), 9000 gal fuel capacity, 335,521 lb dry weight, main engine Cat C32 marine 1300 hp Tier 3 with heat exchanger, Aux engine Cat C15 440 hp tier 3 with heat exchanger, 1740 hp (not including genset), 250 hp at cutter shaft, 54” diameter cutter with 14,900 lb cutting force 18-27-36 rpm. 24” x 66’2” spuds Price: $2,500,000
20” INLAND CUTTERHEAD DREDGE (Ref#3914)
55’ dig depth, 70’ Ladder length, 155’ Length x 34’ breadth x 6.75’ depth, 5’ operating draft, main engine EMD 16-645 (2000 hp), 200 HP hydraulic cutter, HPU Cat 3408, (2) 500 kw Cummins KTA 19 Onan AC generator sets, Pullmaster 50 swing winches, Pullmaster 50 ladder winch, Braden 50 ton spud winch, 24” x 50’ spuds, 48,000 gal fuel capacity, fire detection system, to be sold out of USA Price: $4,600,000
MANITOWOC BUILT 18 CU YARD, 90 TON BUCKET DREDGE (Ref#3706)
Built 1962, 148’ x 43.4’ x 8.2’, 457 GT,. All welded, steel, hull constructed by Manitowoc, full main deck forward fitted with Page Engineering Co. 90 ton rotating crane, aft with deck house with office quarters, galley, mess deck, machine shop and storage area, hydraulic rams for positioning the after spud and an after head space, lower level with air compressors and air receiver, FO transfer pump, bilge pump, fire pump, emergency generator unit main spud Cat D398 generator. Control house above deck house with Pitman 11000 lbs crane. Located Northeast USA. Price: $2,000,000 or best offer
CLAMSHELL DREDGE (Ref#4205)
105’ x 50’ x 8’, Bucyrus Erie 88B crane with 12 Cubic Yard bucket, (2) 30” x 65’ square spuds, (2) H50 Pullmaster winches, 20 KW John Deere generator, set up with weighted spud tension system, will sell crane and dredge separately Price: $3,200,000
2008 BARGE AND ELECTRIC EXCAVATOR (Ref#4075)
200’ x 40’ x 7’ deck barge, Seram MDL S-250.25.E hydraulic balance crane, (2) deck mounted 95 cdy unloading hoppers, 48” trough-belt unloading conveyor, only used in fresh water Price Open
16” ELLICOTT DREDGE (Ref#3948b)
Cat 3508 (low hours), 62’ ladder, 52” cutterhead, 95’ x 24’ x 6’ hull, (2) 48’ spuds, 3 cabins, one bath, 4 beds, office, galley, 150 kw John Deere generator, 150 kw Cummins generator downstairs, located Louisiana, currently being reworked and modernized Price to be Determined
16” x 18” HYDRAULIC CUTTERHEAD DREDGE (Ref#4151) Built 2010, Extensive rebuild/upgrade done 2021, used in fresh water and some brackish water since rebuild, dimensions: 102’ overall length, 83’ hull length x 22’ width x 4.5’ hull depth, 230,000 lb approx. weight, 2.5’ draft (not including spuds), spuds 16” x 42’ length, max dredging depth 45’ (without ladder extension), 54’ with 15’ ladder extension. Can operate with or without idler barge. With the optional idler barge total swing width is 300’. Main engine Cat 3412 (1100 hp @ 1800 rpm), which drives Twin Disc gear attached to GIW pump with 40” impellor. Aux engine (hydraulic power unit) is a Cat 3406 (450 hp @ 1800 rpm). 38” dia Vosta cutterhead, Pullmast winches. Well maintained. Can be dismantled in three days and loaded onto 5 trucks.
Price for dredge: $1,500,000
Available at extra cost:
Idler barge 100’ x 24’ x 4’, with 7000 gallon of internal fuel storage, 2 modified shipping containers used as parts/tool room and break room. Price for idler barge: $325,000
Additional equipment at extra cost:
Dredge pipe 18,000’ 18” HDPE used, pipe anchors, pipe floats, pipe buoys
McElroy pipe fusing machine
(2) booster pumps 16” with Cat 3412 engines with GIW pumps and Twin disc gears
Spare Cat 3412 and Spare Cat 2406
(2) dredge tender boats
16" x 18" CUTTERHEAD DREDGE (Ref#3449)
Built 2012. 102' x 23'6", hull depth 5'. Ladder length: 55'. Minimum depth: 6', max depth 44'. Center section: 36' x 11' x 5'. Side pontoons: 90' x 6' x 5'. Dredge pump: Pearce, 18" x 16". Impeller 40" diameter. Main engine: CAT C-32 Acert 1125 HP (4.369 HOURS) with TwinDisc marine transmission. Fuel capacity: 2000 gallons (shared). Aux engine: CAT C-13 ACERT 440HP with Funk hydraulic drive. Cutterhead type: 43" ID, speed 0-20rpm, 150 HP. Winches: (2) Swing: Pullmaster H-18, Ladder hoist: Pullmaster M-25, (2) spuds: Pullmaster H-18. Spuds: 16" x 75' x 7/8" wall thickness. Standard operator cab, 6'8' with A/C and heat. Modified gantry for longer spuds, stainless steel cutter shaft/sleeve. 2-ton jib crane for pump service. Located Northeast US. Price: $1,775,000
Available at extra cost:
Idler barge with walking spud $300,000
16” x 16” ELLICOTT SERIES 1270 DRAGON DREDGE (Ref#3877)
50’ max dredging depth, 125’ swing width at minimum dreding depth, 92’ swing width at maximum dredging depth, Cat 3508 engine (1000 hp) Marine Tier 3 (heat exchanger cooled), Cat C9 auxiliary engine (350 hp) Tier 3 (radiator cooled), 1350 hp (not including standard genset), 54” cutter diameter, 29-42 rpm, 7991 lb cutting force, 18” x 66’ spuds, 98’6” overall length with ladder raised, 68’ hull length, 26’ hull width including side pontoons, 4’6” depth, (3) pontoons, ¼” and 5/16” plate thickness of center pontoon, 221,000 lbs dry weight, 2’10” hull draft (not including spuds), 6600 gallon fuel capacity. 7 truckloads. Price: $1,600,000
*14” x 14” SHARK CUTTERHEAD DREDGE (Ref#4155e) Built by Dredge & Supply in 2000, 60’ ladder, Cat 3406, needs steel work on side tanks (not below water line), hull in good condition, located in Florida Price: $145,000
Available at extra cost: 4000’ 14” SDR17 DHP dredge pipe Price: $21 per foot
14” x 12” EAGLE IRON CUTTERHEAD DREDGE (Ref#4066)
60’ chain ladder 9” pitch, Mobile pully pump w/Cat 3406b (low hour), the two are connected together (can be splut up or sold together, used in fresh water in Texas Price: $325,000
14" x 12" AAMCO CUTTERHEAD DREDGE (Ref#2787a)
Reworked 2013 / Repowered 1995, Hull rebuilt / refurbished 2014, 65' x 24' x 5', draft 3', 7000 gal fuel capacity. 700 HP CAT 3412 Pump engine, GIW dredge pump, 14" Suction, 12" Discharge. 300 HP Cat 3306 Aux engine, 150 HP Cutterhead drive, 40' Ladder. (2) 16" x 50' stern spuds raised and lowered via winch. (2) 16" x 50' mooring spuds, self-raising and lowering. Hydraulic pumps, motors, cylinders, controls, valves, piping, hoses, and fendering. Firefighting equipment. On blocks, stored on land, excellent condition. Located Northeast USA, in the water. Price: $475,000
14" x 12" AMMCO DREDGE (Ref#3499)
Refurbished in 2009. Main engine: 2011 Cummins KTA38 diesel (1200HP with Murphy Alarms and shutdown, heat exchanger cooled). Pump: GIW 14x12 LSA 36. 34' ladder supports 34" hydraulic cutterhead with 75HP cutter system. Price: $450,000
14"x12" CUTTER SUCTION DREDGE PACKAGE (Ref#3228)
Built 1985, rebuilt 2015. Dredge dimensions: 52' x 24' x 4'. Spuds: (2) 42'. Max dredging depth 28.5', min dredging depth 4'. Dredge pump: PEKOR 12 DMX 32. 14" x 12", impeller diameter 32". Engines: CAT 3412T (600HP). Deck equipment: (2) Pullmaster Swing winches, 8,500lb line pull. 170FPM hauling speed. Idler dimensions: 41' x 20' x 5'.
2000’ of 12” HDPE pipe, spares
PRICE: $250,000
18" x 16" CUTTERHEAD DREDGE (Ref#3313)
Dixie dredge. Built 1986, refurbished 2015. Suction capacity 18". Discharge diameter: 16" length 98’. Width 20.3’. Max dredging depth: 42’. Main engine: CAT D-348, 745 HP. Secondary engine: CAT D-3306, 300 HP. Located West Coast Mexico. Price: $750,000
CUTTER SUCTION DREDGE (REF#1382)
1989, 116 x 32 x 6, submerged ladder mounted dredge pump, ladder length 80’, dredging depth 60’, CAT 3512 main engine, Hydramaster HDMS42 18x16, Suction diameter 18", Discharge diameter 16". Located Northeast USA
PRICE: $1,400,000
15.74" X 13.77" CUTTHEAD SUCTION DREDGE (Ref#1996)
Built 2012 in China – not used) Located in Venezuela, 82’ x 23’ x 6’, steel, 55 net tons, 123 gross tons, main pump Cummins KTA38-M1 (992 hp), hydraulic pump Cummins NTA855M (348 hp), 15.74" suction, 13.77" discharge, Warman Technology dredge pump 300m3/h 65m head 400/550 r/min. Propulsion engine on deck Model ZH41006, reduction gearbox FDLT360 3:1, (2) 6 ton hydraulic winch, 3 ton crane Price: $3,000,000
12” x 14” CUTTER HEAD SUCTION DREDGE (Ref#977)
Refurbished 2008
Dimensions: Length 70’ (21m), beam 20ft (6m), draft 2ft (0.6m)
Machinery/Power: Main pump 750hp 600V DC controlled by SCR drive, total power 1500hp, power supply 4160 v AC
Capability: Digging depth 6 to 45ft (2 to 9 m), can be configured with depths to 60+ft (20m)
Navigation/Position Control: GPS/DredgePack
Additional Information: 4500 feet of SHD- GC underwater power cord on hydraulic power reel, can be run with shore power or 750kw generator, very quiet operation got urban environments
Sitting out of the water since 2014, will need some work but was working well when taken out of water.
Located West Coast USA
PRICE: $225,000
At extra cost:
Spare 600V DC electric motor, (2) complete Thomas 12x14L x 36 booster pumps with 650HP 480V AC with VFD controls & Scada monitoring/control system, unused 12 x 14L x 36 pump and motor for backup, (2) 13000 volt 480V transformers & connecting pipes and valves, low hour GIW 12 x 14L SA36 pump
ELLICOTT 970 CUTTERHEAD DREDGE (Ref#3840)
Built 1981, currently being refurbished, wider pontoons modified, hydraulic spud carriage, 1050 hp Cat 23508 main engine (low hours on rebuild), 16” suction, 18” Ellicott pump with 250 hp hydraulic engine Cat 3306 (4231 hours), located Indiana Price: $1.6 Million
ELLICOTT 890 CUTTER HEAD DREDGE (Ref#3764z)
Built 1981, 11” x 14”, 1000 hp, 79’ hull length, 18” draft, 6’-28’ dredge depth, 130-146’ radius, complete, located Mid West Price Open
12" x 10" ELLICOTT 370 DREDGE PACKAGE (Ref#4086)
Includes Ellicott 370 dredge Cat 3406 engine (Motor has been refurbished with low hours), 10 x 12 booster pump (pump has new sleeve and impeller is in great shape), 1800’ dredge pipe, pushboat with Twin Detroit engines, 6’ x 15’ barge with 14’x8” spuds, 700 gal fuel tank, McElroy fusion machine for fusing pipe w/ shoes for 8”-12” and 18”-20” pipe. Extra new Maddox 8” x 8” pump and gearbox, many other extras and spares. Well maintained and in excellent condition. Located Nebraska Package Price: $225,000
12” X 10” SWINING LADDER DREDGE (Ref#3886)
Built 1997, Rebuilt 2012, 64’4” overall length x 18’6” operating width (11’10” transport width) x 4’ hull depth, 30” mean draft, 750 gal fuel capacity, 83,000 lb approx. total dry weight. 3’ minimum digging depth, 18’ maximum digging depth. In-hull mounted dredge pump (new pump shell in 2014), 12” suction x 10” discharge, impeller diameter 32, flow rate 3250 gpm @ 230’. Twin Disc MG5114 marine style reduction gear (new 2018), coupled to an elastomer style coupling 2.54:1 reduction ratio, located Northeast US Price: $275,000
10” X 12” DSC BARRACUDA SWINGING LADDER DREDGE (Ref#4113a)
Built 2005, 2022 Cat C15 engine, 3’-17’ digging depth, 55’ overall length (with ladder), 17’10” overall width (operational mode), 4’ hull depth, 12’ heigh (less spuds), 38” mean draft (with fuel), 11’11” width (trucking mode), (2) spuds 28’ (1145 lbs) and 30’ (1225 lbs), 70,000 lb total dredge dry weight (approx.).
3’-17’ digging depth,
Swinging ladder - Maximum cut at minimum depth 26’, Maximum cut at maximum depth 19’
Conventional – Maximum cut at minimum depth 80’, Maximum cut at maximum depth 70’
Cat C15 engine, 2828 lb cutting force, 68,000 in/lb operating torque, 88 lb/in cutting force, 28” cutter diameter, 3” shaft diameter, 35 hp cutter rating, 0-32 rpm cutter speed.
Winches: 9617 lb pull (1st layer), 40 ft/min line speed, ½” wire, 208’ drum capacity
Hoist cylinder: 25,535 lb extending force, 41,233 lb retracting force
12” x 10” dredge pump with 32” impeller
Hoist winches: 2204 lb line pull, 81/ft/min, 3/8” wire, 83’ drum capacity
24 VDC battery, 321-645 Delco alternator
800 gal fuel capacity, 150 gal hydraulic oil capacity, operator’s charge, lighted ring buoy, handrails and kick rails, guards, early warning alarm system and engine shut down system, cabin lights, electric bilge pump, replaceable edge cutter, dredge pump priming system, dredge washdown system, high capacity service pump, hydraulic pump/engine clutch disconnect, pump/engine reduction gear, stern pulling eyes,
last used October 2023 Price: $525,000
Available at extra cost:
12” SDR 17 DREDGE PIPE (Ref#4113b) approx. 10,000’ Price: $13 per foot
12” SDR11 DREDGE PIPE (Ref#4113c) approx. 5000’ Price: $13 per foot
10” SWINGING LADDER BARRACUDA CUTTERHEAD SUCTION DREDGE (Ref#4152)
25’ ladder length, 66’l x 17’10”w (with side tanks), 4’ depth, 10’ height (spuds removed), 30” mean draft (with fuel), 10” spud length, digging depth 2’ – 19’, maximum swing (swinging ladder mode) 19’ – 26’, maximum swing conventional mode 76’ x 87’. Cat 3406 KITA engine, Murphy EL-150-K1 day tank sender, R.R. 1000DF cutter gear 71,900 in/lb torque, Cutter’s Edge 5 blade left hand 31’ ½ ID, Fairfield reduction gear 8:1 ratio, Pullmaster winches, 12 x 10 dredge pump, well maintained, currently on landing repairing where needed and painting, located East Coast US Price: $425,000
Available at extra cost:
8500’ of 10” and 12” dredge pipe in excellent condition on trailers, McElroy Fuser and 10” booster
SDR 17 10” DREDGE PIPE (Ref#4126b)
Approx 12000’ in 46-48’ lengths Price: $12 per foot
10” ELLICOTT DRAGON SERIES 370-30 CUTTER SUCTION DREDGE (Ref#4084)
Completely refurbished in 2018, 30’ cutting depth, Georgia Iron works 10 x 12 pump, Cat C15 engine Tier 3, 36’ long, 12’ wide, 4’ deep, 2.7’ draft, 56,000 lbs dry weight, 800 gal fuel capacity, Kubota 6kw 8hp genset, basket cutter: 30kw 40 hp 30” diameter, 4,000 lb cutting force, 2 spuds with hydraulic rope pullers, located Southeast US Price: $445,000
12” x 10” ELLICOTT 370 DREDGE (Ref#4128T)
Built 1984, 36’L x 12’W x 4’ depth, Dredge pump engine Cat 3406, 31.5” cutter diameter w/5 blades, 40 HP, 0-39 rpm, 3840 lb cutting force, 195 lbs/in, (2) swing wiches 8000 lb, 22’ ladder, 16’ digging depth at 45 degrees, 20’ digging depth at 60 degree, 57.5’ overall length, 2000’ of flanged 10” HDPE dredge pipe and (40) 10” pipe floats, located Washington State Price: $275,000
12" x 10" ELLICOTT 370 (Ref#3498)
Main engine: CAT 3406 diesel. Pump: 12" x 10" heavy duty. Modified for increased production, ladder extensions, additional pontoons, and extra spuds. Price: $375,000
10 x 12 ELLICOTT 370 CUTTERHEAD DREDGE (Ref#3166)
(3) Available. Built 1980s. 250 cubic yard per hour capacity. 20' depth capacity. Main engine: CAT 3406 diesel. Dimensions: 36' x 12' x 4', with 2'8" draft. Weight: 56,000lb. Fuel capacity: 800 gal. Cutter diameter: 31". Spuds: 12.75" x 29'. Requires refurbishing. Located Northeast.
Price: $170,000 (less for package)
Dredge pipe:
8,000' of 12" at $13 per foot
2,000' of 14" at $16 per foot
1,800' of 16" SDR11 (thicker than standard SDR17). Some new, some used. 40-45’ lengths. Ends are even-cut with a chainsaw. Price: $18 per foot
BAGEMA CUTTER SUCTION DREDGE (Ref#3711)
Built 1987.18m x7.3m x 2.5m. Depth capacity 35m, max discharge length 1700m, max head dredge pump 8.5 bar, total weight: 80 ton. Cat 3408 (400HP) diesel engine powered jet pump, Linde hydraulic system, Cat 3408 DI-TA 400 HP diesel engine, Reintjes LAF 340 gear box, ratio 2.45:1, 35 kVA generator. Bagema underwater pump (50% wear) , type 30-30 FGH/BW, hydraulic driven, 1.2 m^3/h mixture, Bagema type 30-30 FGH/BW diesel driven jet pump, KSB 400m^3/h @ 8 bar, winch hydraulic driven central drum, 6 drums. 4 point mooring system, ladder winch, suction pipe winch. A-frame, lifting frame, wheelhouse with windows. Location: Germany. Price: $ 358,000
10" x 10" IMS 4010 AUGER DREDGE (Ref#3006)
Built 1991, 38'6" x 9'7" x 9'4", weight 22,000lbs. (2) 35" x 38" x 309" pontoons. Draft 30". Working capacity: Cut 96" wide x 22" deep. Working depth 20'. Engine: Cummins 5.9 177HP, Vickers 3525 hydraulic pump, 2500 gpm slurry pump. Fuel capacity: 180 gal, fuel consumption 13.2 gal/hr. Auger head, cable system. 10" suction, 10" discharge. Used in fresh water. Not used for 1 1/2 years. Located Nebraska. Price: $85,000
10” IMS 4010 AUGER DREDGE (Ref#4087) 16’ depth, 8’ wide, built 2008, new hoses, good shape, located Mississippi Price: $110,000
IMS 7012 VERSI-DREDGE PACKAGE (Ref#3627)
Completely reconditioned 2020 with 2700 hours, all major rework to bring it back to excellent condition. 51'5" x 12' x 10'5" high. Dry weight 47,700lbs. John Deere diesel 6135 AFM85, 13.5L 500 HP main engine with 2,650 hours. Fuel capacity 400 gal. (2) pontoons, 45" x 43" x 468". Draft 35". Working capacity: 11'6" cutter, working depth 30'. Dredge pump: GIW 10" x 12", 5,000gpm at 125' TDH with 2,000' discharge length. Starwheel self-propulsion system.
Package includes:
GIW 10" x 12" Boosters pumps, with 2,000 hours.
Located Florida
Package Price: $675,000
GIW 10" x 12" BOOSTER PUMPS (Ref#3627b) (2) Available. One with 60 hours, one with 2,000 hours. Price each: $165,000
IMS MODEL 7012 HP DREDGE (Ref#4000)
Approx 1600 hours on meter, GIW LCC-M 10” x 12” dredge pump, 500 hp John Deere diesel/hydraulic power unit, positioning boom with 30’ digging depth, hydraulic sand and silt cutterhead with replaceable teeth, Starwheel drive self-propulsion system, enclosed operator’s cab, located Midwest US Price: $525,000
10” CONVENTIONAL DREDGE BUILT BY DREDGE & SUPPLY (Ref#4155c) 12” suction, 10” discharge, Pierce pump, Cat 3406 engine, 30’ ladder (removed but will reinstall), uses 12” dredge pipe, never used in salt water, two owner machine, side tanks to make 18’ wide (removable for transport), located Midwest US Price: $150,000
Available at extra cost: 400’ of used 12” SDR17 HDP dredge pipe (60-90%)
10” x 10” x 30” CUTTERHEAD DREDGE (Ref#4170)
Metso 10” x 10” pump, driven by Cummins KT1150 diesel engine, 40’ ladder, 36” cutterhead, Cummins 855 diesel engine power pack to operate deck winches and cutter head, spud wells (no spuds), enclosed cab with gauge package and vacuum gauge, approx. 400’ of 12” discharge pipe, recently worked, located Southern US Price: $99,500
10” x 8” MUD CAT MC2000 AUGER DREDGE (Ref#3618)
Built 2004. 10" suction, 8" discharge, 6" particle clearance. Engine: John Deere 6081 H 300 HP. Length overall: 47, width overall 8'6", height overall: 8'6". Dry weight: 28,300lb. Draft 2.5' fully loaded. Main pump: Ellicott 24" impeller, capacity: 2500 gpm @ 162' TDH. Sludge pump: Ellicott 25" impeller, 10" suction, 8" discharge, 8" particle clearance. Propulsion: Triple wrap friction drive winch. 2300lbs line pull, 50 fpm max speed. Used in the same freshwater pond since it was new, never in saltwater. 2690’ of 8” HDPE SDR 17 dredge pipe, 1 rubber discharge hose, float for discharge hose. Located Northeast US. Price dredge only: $170,000 Package Price: $205,000
MUDCAT MC2000 AUGER DREDGE (Ref#3608)
4 available from 1999 – 2005, 272 hp Cat engines, the 2001 unit has a Tier 3 Cummins engine with 2500 hours, 24” diameter auger, 20,000 lb torque, 20’ depth, forward/reverse digging, currently on land, located New York Price: $65,000 each
8” CUSTOM BUILT DREDGE (Ref#4140)
8” discharge, 7’ cutter on 21’ elevator (part that moves while cutting), will produce one yard a minute in sandy/silty (not heavy rock) material and will push out at zero elevation 2100’, 2023 Twin 90 hp Yamaha engine, 8’ custom built self-propelled, enclosed cab, with 30’ gooseneck trailer, located Georgia Price: $125,000
MUDCAT SP915 8” AUGER DREDGE (Ref#4191)
15’ depth. 32’ length. Detroit 6 cylinder. 8” discharge. Cutter head width: 98". Capacity: 2000 gallons per minute. Thomas pump. Replaced main gear box – rebuilt box $30k, Located Pennsylvania Price: $80,000
8” ELLICOTT SWINGING LADDER DREDGE (Ref#4176)
20’ ladder, 17’ depth, John Deere 275 hp engine, Georgia pump, handles 4” solid material, located East Coast US Price: $150,000
8” ELLICOTT MUD CAT MC915 AUGER DREDGE (Ref#4150)
6187 hours, Detroit 671N diesel engine, 8” x 8” pump, 9’ wide x 18” max cutting depth, 15’ max operating depth, 39’1-1/2”L x 9’W x 8’8”H, 21” draft, has been sitting for a while, located West Virginia Price: $57,5000
8” MUD CAT AUGER DREDGE (Ref#3917) Manufactured 2005, 2500 hours, 20’ depth, 24” x 96” auger, 8” submersible pump, can produce 228 gpm @ 140’ head, Cat 275 hp diesel engine, New York Price: $75,000
8" MUD CAT AUGER DREDGE LWT (Ref#3652)
8" discharge. Main engine: 6.8L John Deere, 8' auger. 20' depth capacity. New Kerr pump, new hydrostat system, 1000 hours, stored in shed for 10 years, 80 gpm pump, cable winches, 17" impeller. Used in freshwater. Company bought for one job. Spent $40,000 to make it ready for the work and used it to pump 900' 8" pipe relatively thick material at 2500gpm. Cable, anchors, winches. Located Illinois, stored on land. Price: $180,000
8” MUD CAT 115D DREDGE (Ref#3815)
Built 2020, low hours, positioning boom with 15’ digging depth, heavy duty steel hull, 8” Hardox steel submersible dredge pump closed face impeller 125hp John Deere diesel engine, dual 25 hp Yamaha outboard with throttle control self-propulsaion system.
810’ of 8” SDR HDPE pipe
45’ 8’ flat discharge hose
(23) IMS Saddle type pipe/hose floats
Used for one job, excellent condition, on land in Minnesota
75 yards per hours in sludge type material
Price: $250,000
MUD CAT 115D DREDGE (Ref#3731)
Built 2020, used very little (less than one week), 15’ working depth, 8’ cut width, 17” cut height, 22.5” avg draft, Catamaran hull type, John Deere 125 hp engine, 60 gal fuel capacity, MudCat slurry pump with 8” discharge, 3000 gpm max performance, 3.5” solids passage (closed impeller), 4.3” solids passage (open impeller) Price: $240,000
8” VMI 615 HNE MINI DREDGE (Ref#4146)
Built 1996, 8” discharge, electric powered (150’ power cable included) 480V, approx. 240’ hose, cable driven, used in fresh water only at municipal facility pond, 44’ x 11’W, located Nevada Price: $50,000
8” VMI 815 AUGER DREDGE (Ref#4069)
Built 1998, Warman ladder mounted 8” pump, 350 hp Cummins M11 engine with 3500 hours (recently rebuilt). Recently invested $150,000 into the dredge including: rebuilt engine, all new hydraulics, all new hoses, all new wiring, all new dredge steel and flex hose piping, brand new cutterhead, teeth and shroud and protective cage, rebuilt dredge pump with new impeller, structural and hull work. Located Texas Price: $110,000
6” CUSTOM HYDRAUILC SUCTION DREDGE (Ref#4203)
Gulf Atlantic 6” dredge pump mounted on a custom galvanized dredge arm, 10’ digging depth, can be upgraded to an 8” pump, John Deere hydraulic power unit powers the hydraulic pump. TB290 excavator mounted on barge chassis through the deck, hull 34’ x 12’+, good condition, highly maneuverable and transportable, lift pad eyes, The barge features a robust frame construction suitable for operation in shallow water, maneuverability is achieved with precision using the dredge arm and winch powered spuds, includes 400’ dredge pipe, floating gear and galvanized 25 yard dewatering bin, good condition, located in Florida Price: $250,000
6” X 6” VMI AUGER DREDGE (Ref#4155a) Uses 8” dredge pipe, 20’ depth, 8’ wide auger, ladder mounted 6” x 6” pump, 350 hp Cummins engine (rebuilt out of frame), never used in salt water, located Midwest USA Price: $75,000
8” MUDCAT AUGER DREDGE (Ref#4155b) Mudcat pump, 19’ depth, 8’ wide auger, located Midwest US Price: $65,000
MUD CAT 40E ELECTRIC DREDGE (Ref#3806)
800’ lay flat hose, 600’ power cord, radio remote control with handheld remote, 4-point winch anchoring system, 600’ traversing cable, auto sense, black saddle floats. 24’3” overall length x 8’4” operational width, 16” draft. Floatation: (2) 28” dia x 10’ pontoons, working capacity: 7’6” wide, 14’ depth, 40 hp electric driven slurry pump, 6” suction, 6” discharge. Located Northwest USA Price: $165,000
SRS CRISAFULLI SD110 AUGER DREDGE (Ref#4131)
Manufactured 2010, Perkins 110 hp engine (dredge has 640 hours), Yamaha 116 hp engine (approx. 270 hours), sitting since 2017, excellent shape
2012 Kearney trailer for piping with approx. 500’
2004 Hillsboro trailer for dredge
Located Iowa
Price: $150,000
SRS CRISAFULLI SD110 AUGER DREDGE (Ref#4056)
Manufactured 2012, 1400 hours, Perkins 110 hp engine, 1200’ of 6” solid dredge pipe, 300’ floating pipe, used in fresh water only, currently on land in Ohio (new cost $360,000) Price: $265,000
CRISAFULLI 6000 ROTOMITE DREDGE (Ref#1307)
Built 2003, 6 x 8" pump/dredge discharge, 32’ x 8’5"W x 9’5"H, weight 18,000#, self-propelled, 0 – 20’ depth capacity, 275 hp John Deere engine, 8’5" cutterhead width, discharge 2500 gpm @ 80’ TDH water and produces up to 150 cubic yards per hour, located Mexico Price: $240,000
8" SWINGING LADDER DREDGE (Ref#3580)
Overall length: 42', Overall width (swinging ladder mode) 17'4". Overall width (trucking and conventional) 10'6". Hull depth 3'10". Height without spuds 10'6". Average draft 2'8". Ladder length 22'. Spuds: 6" x 8" square. Dredge dry weight: 38,600lbs. Max dredging depth 16'. Main engine: CAT 3126 (260 HP @ 2600rpm) radiator cooled. Cutter diameter 30", cutting force 2,690lb. Swing winches: DSC 5,150lb line pull, 65'/minute. Swing force 27,600lb, 12'/minute. Dredge pump: DSC 8"x8", 19 3/4" diameter impeller. Complete with 24 different spare parts available. Price: $250,000
8” CUTTERHEAD SUCTION DREDGE (Ref#4041)
Built 1988, 6 x 8, 47’ overall length (ladder up), 30’ hull length, 11’10” beam, 4’ depth, 20’ ladder length, 1000 gal fuel capacity, approx. weight 47,000 lbs, 17’ digging depth, hull center 22’ x 5’10” x 4’, sponsons 30’ x 2’11” x 4’, control room provides 360 degree visibility (top portion removable for transport), 6” x 25’ spuds, 26” ID 5-blade cutterhead 20 hp 34 rpm, Pekor 6 x 8 dredge pump, Pullmaster 9600 b swing winch, Pullmaster 2000 lb spud winches, Nopak 4 x 48 ladder ram, 1800’ 8” HDPE dredge pipe Price: $335,000
8" AMMCO SWINGING LADDER DREDGE (Ref#3480)
Model PCD-8C-M
Manufactured 1984, good condition, well maintained
Equipped with a stern mounted travelling spud; by a simple reconfiguration of spuds and swing wires it operates in the conventional swing mode.
3 piece hull: center section 30’ x 8’ x 4’, side pontoons 37’ x 5’ x 4’. Assembled dims 37’ x 18’ x 4’
Swinging ladder 31’ long for dredging to depth of approximately 25’
Heavy Duty 10" x 8" AMMCO dredge pump, 24" impeller diameter
Cat 3408 diesel engine (365 hp) continuous @ 1800 rpm
3-stage hydraulic pump for all hydraulic functions including cutter drive, swing winches, ladder and spud hoisting cylinders, and spud travel cylinder
New 10 kw generator for lighting and AC electrical outlets
Charter: $35,500 per month (2 month minimum)
Purchase Price: $385,000
8” X 8” DSC MORAY DREDGE (Ref#4185c)
42.8’L x 18.5’W, 17.5’ depth, 42,000 lb overall weight, 19.5” impeller dredge pump, 25 hp cutter power, cylinder ladder lift/swing, 8” square spud, articulating rear spud, Cat 275 hp diesel engine, inline direct marine style transmission for dredge pump reduction, PLC operating system, standard equipment, power up/down winches for proper cable storage, stern kicker spud or extending leg for controlled positioning, located Florida Price: $300,000
8” MORAY DREDGE (Ref#4155d) Built by Dredge & Supply in 2000, Cat engine, submersible pump, needs sandblast and paint, hull in good condition, located Midwest US Price as is: $90,000
8" x 8" W & S MODEL D20 CUTTERHEAD DREDGE (Ref#3511)
Built 1999, 130 hp Cummins, 15’ depth, Pekor 8 x 8 x 25 pump, approximately 3000’ of DR17 pipe with trailer, 18’ welded bottom work skiff with air cooled engine, misc pipe floats, 8" and 10" rubber hoses, exra spuds, extra pontoons, ladder extension, misc pipe elbows and reducers, spare parts and equipment Price: $200,000
UMI MUD CAT MS16 TRASH SKIMMER (Ref#3424)
Built 1992. Mudcat model MS16 - 12000B. Pick up capacity: 16' wide x 2 1/2' deep. Storage capacity: 12,000lbs or 700 cubic feet. Main engine: Cummins 5.9L engine (needs remanufacture) Pontoons need to be replaced. Propulsion system: (2) hydraulically driven, bidirectional and variable speed propellers. Hydraulic tank capacity: 100 gallons. Hull dimensions: 34'8" x 11'11". Light draft: 17", loaded draft: 26". Number of compartments: 10. Located Virginia. Price: $60,000
SMALLEY DREDGER (Ref#4089b)
Built 2004, (yellow), good condition, ready to work Price: $62,000
SMALLEY DREDGE (REF#4089c)
Built 1989 (green), fresh rebuilt motor but needs cylinders repacked Price: $52,000
DRAGLINE / DREDGE / SPUD / QUARTERS BARGE (Ref#3149)
Built 1981, 150' x 50' x 9.5'. GT/NT 806. American Hoist triple drum waterfall chain driven spud winch powered by Detroit Diesel model 6-71. Winch operates single forward 50' and (2) aft 35' x 32" square spuds. Deck house / crew quarters. Accommodations for (13) in (7) bunk rooms. Washroom, galley. (2) Single stage Quince Model 340 compressors, (2) lube oil tanks.
Crane: PAGE Model 721 revolving crane, built 1956. 130' boom. Powered by 500HP CAT D379 diesel, generators: (2) John Deere. (2) 8 yard dragline buckets (one for rocks). Located US Gulf. Price: $2,800,000
DREDGE PACKAGE FOR SALE: (2) EXCAVATOR DREDGES / (1) BARGES / (2) PUSHBOATS (Ref#3882)
2 dredges (yellow dredge is ready to work, green one has cylinders leaking but has a fresh built motor), 12-15’ depth capacity, can operate in min of 1-1/2’ water
1 barge: 10 x 25 x 4 (new inner liner)
2 pushboats with 25 hp Mercs and trailers
Located Wisconsin. Two truckloads (1 barge and 1 dredge on each truck)
Package Price: $110,000
EXCAVATOR DREDGE PACKAGE FOR SALE (Ref#4186) – 14’ depth, 500-700 yards per hour
(2) 40’L x 12’W haul barges
(1) 30’L x 12’W hopper barge
40’ x 10’ Single engine tug (5 years old)
335 Excavator (6 years old) mounted on 24’ x 12’ barge with floats for stabilization (making it 40’)
Portable steel wall so they can work against the wall
442 Bob Cat excavator (8 years old)
20’L container with spare parts and tools
Cold-tarred on bottom, used in fresh water only (used mainly on golf courses and condo village lakes, etc)
All equipment can be hauled on trucks
Located Illinois
Package Price: $275,000
KOMATSU PC450 LC EXCAVATOR (Ref#2880)
2010 Komatsu PC450 LC (Long Carriage). 350 Horsepower. 60' Boom, self-unloading counter-weight excavator. Located New England. Price: $190,000
CAT LONG REACH ATTACHMENT (Ref#C40)
Built 2006. 2500 hours. Not used in 6 years. 64' capacity. Located Iowa. Price: $25,000
TRAILING SUCTION HOPPER DREDGE (Ref#3964)
1.459 tdw on draft 4.687 m, Built Cassens Germany in 1975, converted to dredger in 1999, Insb class, Dims 75.0 x 10.2 x 5.5 m, MAK 883 kW main engine, Bowthruster, Speed 10 kn, Dredging dept 23 meters trailing pipe, Diam suction pipe 0.55 cm, Loading and discharge time about one hour, Only overboard pumping , no bottom discharge. Dredging pump Warman driven by caterpillar 3412, Jet pump Warman driven by caterpillar 3406. Vessel is well maintained. Sale only outside North Europe (Baltic States permitted). Price: 2,700,000 Euro.
SUNDREAM 24 X 10 PUMP (Ref#4063a)
300 kw, 460 rpm, 3200/3800 cubic meter per hour Price: $65,000
HAGLER 20” BOOSTER PUMP (Ref#4144d)
Cat C3512 diesel engine 1395 hp @ 1800 rpm, GIW?TBC 20x20 – 46.7 JF c/3ME L pump, Atra Flex T8 coupling torque rating 333,500 lb/in, ZF/4650 transmission,, 1653 hp continuous rating @ 1653 rpm, ratio 3.040:1 Available for Rent
GIW INDUSTRIES 18LSA44 19” BOOSTER PUMP (Ref#4144b)
Mitsubishi S12R-MPTK diesel engine, 940 kw at 1600 rpm, Masson MMW 5700 gear box ratio 1:3,133, 18” suction, 18” discharge, dimensions: 21 x 9 x 10.5’ Available for Rent
16" PUMP (Ref#1940)
Built 1977, Metso Thomas P46, was powered by CAT 1300 HP Diesel engine. Dimensions and weight: 138"L x 71"W 86"H, 22,000#. Removed from a dredge which was converted for another use. Located California. In good working condition when it was stored. Price: $70,000 PRICE REDUCED: $40,000
16” x 16” MADDOX BOOSTER PUMP (Ref#4050)
Detroit 12V92TI diesel engine, mounted on skid, complete, no fuel tank, located Florida Price: $65,000
Videos Available
https://youtu.be/0qpkM17Uz0A
https://youtu.be/IGPGakIN4Cg
https://youtu.be/TC_jrZEeh0w
16" x 14" GIW BOOSTER PUMP (Ref#3629a)
Remanufactured 2014. Model 939S. Powered by Detroit Diesel 16V92, 700 HP, 3.48-1 gear ratio. Approximately 9600 hours. 97% life left on pump, minimal wear on liner and impeller, no cavitation marks, new shaft wear sleeve. Peerless 3x4 water service pump. Skid-mounted. Guards, rails. Located Mid South USA. Price: $320,000
ELLICOTT 16” BOOSTER PUMP (Ref#4144a)
Ellicott close coupled reduction gear box, Cat C27 diesel engine with clutch, Ellicott 16” ID suction cleanout, radiator cooled engine, service water pump and drive, skid base Available for Rent
14” X 14” PIERCE BOOSTER PUMP (Ref#4155f) 700 hp Cat engine, located Midwest US Price: $95,000
12 x 12 PETTIBONE BOOSTER PUMP (Ref#4155g)
12V71n Detroit diesel engine 450 HP. Pettibone pump, could use new impeller, turns at 600rpm, new transmission, Located Midwest US Price: $60,000
12 x 12 METSO BOOSTER PUMP (Ref#4155k)
700 hp Cummins engine, very good condition Price: $100,000
BOOSTER PUMP (Ref#866)
Built 2000, 14" x 14", (2) 450 hp electric motors, located Midwest USA Price: $160,000 PRICE REDUCED: $145,000
14x12 BOOSTER PUMP (Ref#2845)
Built 2009, 14" suction, 12" discharge, 22" impeller. 400 HP Cummins diesel, 24 volt start, 18 speed transmission with clutch, shaft drive. Mission Magnum XP pump example performance data: 14" x 12" x 22" impeller @ 1200 rpm, 400 HP, with a 250' head will pump 5000 gallons per minute. Located Western Canada. Price: $40,000
12” x 10” ELLICOTT BOOSTER PUMP (Ref#4202)
Built 2009, John Deere 6090 engine, producing 325 hp Price: $195,000
GIW 10" x 12" BOOSTER PUMPS (Ref#3627b) (2) Available. One with 60 hours, one with 2,000 hours, Rocky Mountains. Price each: $165,000
10" x 10" GOULDS PUMP (Ref#3317)
Built 1996. Goulds model 5500. Hours: 2609. Size: 10"x10". Excellent condition. Skid mounted. Fuel cell, pulleys, belts, pump manual. Located Midwest USA. Price: $40,000
ELLICOTT 10” BOOSTER PUMP (Ref#4144c)
Cat 32 Tier 4 Final Industrial diesel engine, Ellicott close coupled reduction gear box, radiator cooled diesel engine and heat exchanger cooled gear box and clutch, service water pump and drive, skid base, fully enclosed engine and clutch Available for Rent
DRAGFLOW EL20 SLURRY PUMP and DRAGFLOW EL35 SLURRY PUMP (Ref#9520T)
EL20 has 100 hours, EL35 never used. Both units have starter panels and cords, located Canada, immediately available Price for both pumps: $58,500 USD
10" HOBART SUBMERSIBLE DREDGE PUMP (Ref#1162)
.200’ of electric cable, discharge hose, 225 kw Cat portable generator Price: $85,000
16 sets of 24" bells and balls (Ref#3436) 75% good
Price: $8500 per set
22” SDR17 HDPE Dredge Pipe (Ref#4144e) 15,000’, East Coast US Price on Request
DREDGE PIPE AND FLOAT COLLARS (Ref#4167)
2000’ of 18” diameter DR17 ISCO dredge pipe (50’ lengths) Price: $27 per foot
(10) 18” flange adaptors with backing rings Price: $295 ea
(30) 24” Neptune clamp on float collars Price: $990 ea
(55) 18” Neptune clamp on float collars Price: $795 ea
16” SDR 17 Dredge Pipe (Ref#3569) 12,000 LF (saw cut to 40’-50’ lengths, some with couplings) Price: $13 per ft
8” SDR17 HDPE DREDGE PIPE (Ref#4179a) 300’ available, 40-50’ sections, located Florida Price: $8 per foot
10” SDR17 HDPE DREDGE PIPE (Ref#4179b) 750’ available, 40-50’ sections, located Florida Price: $12 per foot
12” SDR17 HDPE DREDGE PIPE (Ref#4179c) 24,300 ’ available, 40’-50’ sections, located Florida Price: $15 per foot
750KW GENERATOR (Ref#3411) 480v / 3 phase / 60 cycle. Powered by CAT 3508 diesel engine, 1000 HP. Mounted in 40' trailer with (2) 1000 gallon fuel tanks. Was used to power a dredge. Located Midwest. Price: $55,000
500 KW CATERPILLAR GENSET (Ref#4155h) 900 hours, serviced, Cat 3412 engine, located Midwest US Price: $50,000
4000’ 14” SDR17 HDP dredge pipe (Ref#4155i) Price: $21 per foot
3,200’ of 14” SDR DREDGE PIPE (Ref#3315)
Some new, some near new, SDR 17, 40-50’ lengths
Sold loaded on truck in Midwest US
Price for flanges: $150 each
Price for dredge pipe: $22 per foot
12” SDR 17 DREDGE PIPE (Ref#4113b) approx. 10,000’ Price: $13 per foot
12” SDR11 DREDGE PIPE (Ref#4113c) approx. 5000’ Price: $13 per foot
7000’ of 12” DREDGE PIPE (Ref#3997b) 12” DR17 HDPE dredge pipe with flanges and rings for 300’ sections, pipe has now been cut into 100’ lengths for storage, located West Coast Price: $90,000
12” DREDGE PIPE (Ref#3941)
6800’ of 12” HDPE SDR17 dredge pipe, cut ends, 40’ lengths, some connectors $14 per foot
2800’ new 12” HDPE SDR17 dredge pipe, factory cut ends, 40’ lengths $22 per foot
3000’ 8” HDPE SDR 17 dredge pipe with connections, like new, loaded on truck $13 per foot
8” SDR17 HDPE DREDGE PIPE (Ref#4179a) 300’ available, 40-50’ sections, located Florida Price: $8 per foot
10” SDR17 HDPE DREDGE PIPE (Ref#4179b) 750’ available, 40-50’ sections, located Florida Price: $12 per foot
12” SDR17 HDPE DREDGE PIPE (Ref#4179c) 24,300’ available, 40’-50’ sections, located Florida Price: $15 per foot
Let us know if you have any vessels, barges, dredges or related equipment for sale.
Keep us in your files for any equipment that may become available in the future.