CABLE TOOL RIGS

        05/18/2017     
    

 

BUYCRUS ERIE 60L   (Ref#2418R) 

bucyrus erie 60l

Skid mounted oak timber & 2 1" I beams 8', Mask-Approx 48ft. H  4 guy wires from top of mask & braces, Raised by worm gear winch, misc. wire
Approx. 2200' 7/16 used sand line      divider chain driven
Approx. 2200' 3/4 used drilling line      divider gear driven
Gear driven tubing winch 5/8"line  2 line or 3 line Engine 6 cyl. Hercules (gasoline ) ( propane ) or (natural gas ) extra carburetor regulator Rig gears drilling line high & low  sand reel 1 speed  tubin winch 1 speed All gears have reverse
Tools:
Circle track  jack wrenches to tighten bits & sockets  handle & brace
3 change over subs
4 sets jars drilling & fishing
1 combination socket for fishing out stems or pipe
1 latch socket for fishing bailing out
1 8" drive head
1 drive pipe clamps to put on stem squares
1 extended crane mounts off mask, for chain hoist has trolley
1 peerless chain hoist
1 32' stem & rope socket
1 5 1/2 " bailor w/ extra bottom
2 6" bits 3'6" 2 1/2 x 3 1/2     1 bit 4 1/2"   2'10"    2/1/4 x 3 1/4
1 8" bit 2 '6"   2 1/2x3 1/2
6 box pin caps w/ welded loop for stem or jarer bits made to pick up w/ tubin block
1 tubing block 3 line 5/8" to 1"line
1 bit swivel wrench hooks on chain hoist
1 used extra spud pitman
1 casing tester runs off bailor
3 new brass bushings
2 new chain sprockets runs sand reel
1 swabbing gear bracket & gear shifting handle
1 stem guide mounts middle mask
2 2" used water pumps Briggs & Stranton
1 blower mounted on rig frame runs off flat belt pulley off engine
1 approx. 10' to 12' heavy duty chain C hooks to pull rig
Price:  $33,000


BUCYRUS ERIE 60L (Ref#3308N

Manufactured 1958, 3 lines, Waukesha 6 cyl propane, mounted on trailer, 4000’ of of brand new 5/8” drill line,  2800’ of’ 7/16” sandline, ¾” block line, good gearing, good brake bands, new sheaves, new spudding beam, braces included, 4 new tires, newer axle, 46’ mast, no tools, currently drilling  Price:  $50,000  PRICE REDUCED:  $39,500 – Kentucky 


BUCYRUS ERIE 36L  (Ref#8420Tb

Cat engine (not installed), tons of tools, 5” drill stem, bits  Price:  $48,500 - Oklahoma


BUCYRUS ERIE 28L (Ref#6780N)

bucyrus erie 28l

Manufactured late 1960’s, Waukesha diesel deck engine, mounted on Mack 800 tandem axle truck with diesel engine, 3 line machine, 55’ mast, 3 sheave block, 400+’ of ¾” casing line, 4000’ of ¾” drill line, 4500’ of 7/16” sandline, 1 front & 2 rear hydraulic leveling jacks, tools available 4” up to 10”, currently drilling  Price:  $45,500 - Kentucky


BUCYRUS ERIE 24L  (Ref#8378T

John Deere diesel engine, 3 line block, casing strut, ¾” drill line, ½” sandline, mounted on trailer with 5th sheel hitch, floors, doghouse and drilling tools  Price:  $44,500 - Ohio


BUCYRUS ERIE 24L  (Ref#11458R

bucyrus erie 24l

Trailer mounted, diesel engine, 3 line machine, 450’ of 7/8” new drill line, tooled, located Mexico  Price:  $39,500


BUCYRUS ERIE 24L (Ref#7003N

bucyrus erie 24l

4 cylinder Perkins diesel deck engine, mounted on late 1960’s International tandem axle with Red Diamond gas engine, new winch line, 1800’ of new ¾” drill line, 1800’ of new ½” sandline, 1 front & 2 rear screw jacks, tooled up for 4”, new hydraulics, new clutches, tubing power tongs, all gears good condition, currently drilling 

Price:  $48,500 - Ohio


BUCYRUS ERIE 24W (Ref#7895R)

bucyrus erie 24w

Allis Chalmers propane deck engine, mounted on late 60’s-early 70’s Chevy tandem axle truck with gas engine, 40’ mast, 3 line machine, 800’ of ¾” drill line, 1200’ of bailing line, lots of tools, 6” – 15”, bits, stems, jars, wrenches, bailers, etc., 3 rear screw leveling jacks, running now  Price:  $50,000 – Colorado


BUCYRUS ERIE 24W  (Ref#4636R) 

bucyrus erie 24w

3 line, 400’ drill line, hyd pump, mounted on 5 wheel axle truck, Internatiopnal 4 cyl diesel engine, doghouse, pipe trailer
Tooling:
Sinker bar 20’ x 4-1/2”,, 2-1/4” x 3-1/4”
Rope Socket:  2-1/4” x 3-1/4”
Sinker Bar 20’ x 4-1/2”, 3” x 4”
Rope Socket 3” x 4”
Bit, button 2-1/4” x 3-1/4”
Bit, Mother Hubbard 8”, 3” x 4”
Bit, Mother Hubbard 12”, 3” x 4”
Bit, Mother Hubbard 16”, 3” x 4”
Bit, Star 12”, 3” x 4”
Bit, Under Reamer 6”, 2-1/4” x 3-1/4”
Jars, Drilling 2-3/4” x 3-3/4”
Jars, Drilling 2-1/4” x 3-1/4”
Jars, Fishing 2-3/4” x 3-3/4”
Jars, Fishing 2-1/4” x 3-1/4”
Bailer, Dart 8” x 15’
Bailer, Dart 6” x 20’
Bailer, Flat Bottom 4” x 12’
Bailer, Flat Bottom 8” x 15’
Bailer, Suction 7” x 12’
Bailer, Suction 9” x 12’
Bailer, Suction 6” x 10’
Bailer, Suction 8” x 10’
Bailer, Suction 12” x 15’
Swedge 6”, 2-1/4” x 3-1/4”
Swedge 8”, 3” x 4”
Swedge 16”, 3” x 4”
Fishing Tool, Mills, no jaws
Fishing Tool, Mills, no jaws
Wrench, J, Right, with slips
Wrench, J, Left, with slips
Surge Block 3’
Perforator, casing, 8”, 12”, 16”
Drive Head, factory 6”
Drive Head, factory 8’
Clamps, Casing Drive
Saver, Cable, 15 lbs.
Heads, drive
Elevators, casing & pipe
Blocks
Hooks and slings
Price:  $35,000 - Utah - DEAL PENDING


BUCYRUS ERIE CABLE TOOL RIG  (Ref#3093T) 

3 lines, gas on deck, mounted on 1979 Mack 700 truck with diesel engine, 1000’ of new mainline, driller’s platform, cathead  Price:  $21,500


BUCYRUS ERIE 22W  (Ref#1901T) 

3 line machine, 40’ mast, Continental gas dweck engine, mountedon mid 1980’s Ford F700 truck with Cat engine (transmission needs work), 2 rear screw jacks, tooled up for 7” holes, bailer, bit, stem, etc, running now  Price:  $33,500 - Kansas


BUCYRUS ERIE 22W  (Ref#9616N

Manufactured 1960’s, mounted on 1971 tandem axle International truck with gas engine, 3 line machine, cathead, 6 cyl Continental engine on deck, 

Price:  $29,500  PRICE REDUCED:  $20,000 - Florida


BUCYRUS ERIE 22W  (Re#14986Ta)  Built 1953, mounted on 1979 Mack truck, lots of tools, ready to drill  Price:  $28,500 – West Virginia


BUCYRUS ERIE 22W (Ref#13313T)

Series II, 3 line machine, rebuilt late 90’s, Ford 300 ind gas deck engine, mounted on 1983 Mack single axle truck with Mack diesel engine, Lincoln welder, 3 hydraulic leveling jacks, running now  Price:  $27,500 - Illinois
Tools available at extra cost


BUCYRUS ERIE 22W-III  (Ref#7204T) 

Manufactured 1976, 300 Ford deck engine, mounted on 1993 GMC truck with dieselengine, air brakes, 3 line machine, 46’ mast with extension  Price:  $53,500


BUCYRUS ERIE 22W  (Ref#6354T

Diesel engine on deck, mounted on 2000 GMC C Series truck with diesel engine, drill stem, 300’ left lay cable  Price:  $34,500 PRICE REDUCED:  $30,000 - Alabama


BUCYRUS ERIE 22W  (Ref#8420Ta) 

Built 1967, only used 2 years, stored inside, needs some work, 30,000 miles on truck, 4” 20” stem  Price:  $28,500 - Oklahoma


BUCYRUS ERIE 22W (Ref#3136T)  Converted to Series III, 3 line machine, 500’ of mainline, 750’ of sandline, 150’ of casing, Cat deck engine, mounted on Chevy truck with gas engine, 3 leveling jacks, jars, stems, 6-18” bits, assorted bailers  Price:  $67,500 - California


BUCYRUS ERIE 22W SERIES II  (Ref#7194Ta

Completely rebuilt, 42’ mast, unmounted, 1250’ of ¾” main line, rebuilt jack shaft, new clutches, new pinion gear, new bushings  Price:  $54,500 - Indiana


BUCYRUS ERIE 22W  (Ref#2564R

Manufactured 1971, 3 lines, 227 / 6 cyl Continental engine on deck, 50’ mast, mounted on 1981 Ford truck with 6.1 liter engine, 7 leveling jacks, jar bar, wrenches, misc tooling  Price:  $19,500 – New York


BUCYRUS ERIE 22W  (Ref#2679T

bucyrus erie 22w

Ford diesel 60 hp deck engine, mounted on 2003 Freightliner truck with 300 Hp Cat enginer, 3 hyd jacks, 42’ mast, 2 lin3e machine, 400 mainlines, 400’ sandline, rebuilt 2006  Price:  $54,500


BUCYRUS ERIE 22W  (Ref#6699T) 

Ford diesel deck engine, mounted on Ford F800 truck with gas engine, 3 line machine, 42’ mast, tooling ncluded:  bits, drill stem, etc  Price:  $32,500


BUCYRUS ERIE 22W  (Ref#12184) 

bucyrus erie 22w

Manufactured 1970’s, completely rebuilt 2000, 4 cyl Ford Industrial gas engine on deck (rebuilt), mounted on 1984 International single axle truck with gas engine, new crowd, jack shaft, etc., 3 line machine, 800’ of ¾” main line, sandline, casing line, cathead with rope, basic tooling, jars, bailers, bits, etc, good condition  Price:  $30,000 – Oregon


BUCYRUS ERIE 22W (Ref#12404R)

bucyrus erie 22w

Ford 172 ind gas deck engine, mounted on ’66 GMC with gas engine, 3 line machine, 500’ new ¾” drill line, 400’ of 3/8” sandline, 100+’ of ½” third line, 1 front & 2 rear mechanical leveling jacks, sitting but running when parked  Price $37,500 – Maine


BUCYRUS ERIE 22W (Ref#3858R)

bucyrus erie 22w

3 line machine, Continental gas deck engine, mounted on 1971 International with gas engine, approx 500’ of drill line, stored inside, no leveling jacks, 6” tools  Price:  $47,500 – North Carolina


BUCYRUS ERIE 22W  (Ref#10449R

bucyrus erie 22w

Manufactured 1957, 4 cyl Perkins diesel engine, 3 line machine, auto braces, mounted on 1974 R Model Mack tandem truck with diesel engine, 48,000 GVW, air brakes, 5 speed transmission, detached single berth sleeper converted to tool box, (4) 36” stroke jacks, no leaks, tooling 
1989 MACK MIDLINER CABOVER WATER/SERVICE TRUCK  diesel engine, 22’ steel flatbed with no rust, 225 gallon water tank, 225 amp Miller GBobcat welder with 50’ cables, electric crane with remote, Oxy and Acetylene burning outfit complete with 50’ hoses, gauges and torches, 33,000 GVW, air brakes, 6 speed transmission
PACKAGE PRICE:  $50,000 - Pennsylvania


BUCYRUS ERIE 22W  (Ref#1054R

bucyrus erie 22w

3 lines, 6 cyl Hercules deck engine, mounted on 1964 International Loadstar 1800 with 465 gas engine, comes with full string of tools, rig and truck run great  Price:  $38,500 - Arizona


BUCYRUS ERIE 22W  (Ref#4367N) 

bucyrus erie 22w

3 line machine, cathead, new Continental gas deck engine (very low hours), mounted on 1987 GMC single axle truck with 427 gas engine, telescoping mast, automatic braces, rope socket, some bits and tools, toolbox, catwalks, 2 rear mechanical jacks, 450’ of 5/8” drill line, 450’ sandline, tooled for 6” and 8”, drills daily  Price:  $34,500 PRICE REDUCED: $29,500 – Wisconsin 


BUCYRUS ERIE 22W  (Ref#10751R

bucyrus erie 22w

3 line machine, Continental engine, mounted on 1967 all wheel drive Military truck  Price:  $23,500


BUCYRUS ERIE 22W (Ref#1881R)

bucyrus erie 22w

3 line machine, Ford gas deck engine, mounted on 1984 Ford F700 with diesel engine (not 4x4), 44’ mast, 1 front & 2 rear hydraulic leveling jacks, tooled up for 6”, ready to go  Price  $39,500


BUCYRUS ERIE 22W (Ref#9916R)

bucyrus erie 22w

3 lines,  6 cyl Ford Industrial gas deck engine, 500’ of ¾” Mainline, 700’ of 5/16” sandline, mounted on 1984 Dodge with V8 gas engine, 2 rear mechanical jacks, 4” to 6” tools, 6” & 8” bits.  Price:  $29,500 - Kentucky


BUCYRUS ERIE 22W SERIES III  (Ref#8392R

bucyrus erie 22w series III

3 lines, manufactured 1977, 6 cyl Continental engine on deck, 40’ derrick, 140 gal propane tank, mounted on 1966 Ford 850 tandem axle truck with 534 gas, hydraulic jacks, stem, rope socket  Price:  $50,000 - Washington


BUCYRUS ERIE 22W (Ref#4217R)

3 line machine, John Deere diesel deck engine, 5’ mast extension, mounted on 1976 Chevy 2 ton with gas engine, many rebuilds, new clutches, 1000’ of 3/8” sandline, 1000’ of ¾” drill line, good running condition  Price rig only:  $39,500   Price with 6” – 10” tools:  $44,500 – Idaho


BUCYRUS ERIE 22W  (Ref#7248R) 

bucyrus erie 22w

3 line machine, gas deck engine, mounted on 1969 Ford Cabover with gas engine, 2 front and 2 rear mechanical jacks, no tools  Price:  $21,500  -  California


BUCYRUS ERIE 22W (Ref#15094R)

Bucyrus Erie 22W

Detroit 353 deck engine, mounted on 1974 International with Detroit 6V53 engine, 3 line machine, screw jacks, tooled up for 6” & 8” holes, well maintained, sitting but running when parked  Price:  $35,000 – Montana


BUCYRUS ERIE 22W (Ref#14321R)

bucyrus erie 22w

3 line machine, 3 cyl Duetz diesel deck engine, only 1000 hours, mounted on 1981 GMC with Cat 3208 engine, 1000’ 3 /4” cable, 1000’ 7/16” sandline, tooled up for 6” & 8”, bits, subs, stabilizers, jars, wrenches, etc. 1 front & 2 rear mechanical leveling jacks, ready to go  Price:  $44,000 PRICE REDUCED: $39,500  – Connecticut


BUCYRUS ERIE 22W (Ref#6083R)

bucyrus erie 22w

3 line machine, 750’ of ¾” mainline, 750’ of 3/8” sandline, 6 cyl Hercules gas deck engine (887 hours on overhaul), 2 catheads, hydraulic pump system, mounted on Mililtary 2-1/2 ton 6x6 with 6 cyl White/Kaiser diesel engine, 25,000 miles, multi-fuel front end power winch , needs drive shaft to PTO spare drive belt, 2 rear hydraulic leveling jacks, spare engine parts,  fully tooled up 6” to 16”,
Tooling:
(5) 6” bits
(3) drill stems (19’-20’ long)
6” bailer, 4” bailer
6” sand pump bailer
(2) Rope socket
(2) 8” bits
Bumper bar for gogging tooling loose
1 set drilling jars
Breakout wrenches (2 sets and 2 sizes w/chain tensioner bars)
Set drive blocks, drive bar
15” bit (can be reduced to 14”)
12” bit expanded to 14”
Drive bucket for 6” casing, variable weight capability end caps, lifting eye, misc spare parts
Ready to go.  34’L x 8’W (11’ w/mirrors) x 12’ high 

Price:  $34,500 - Montana


BUCYRUS ERIE 22W  (Ref#11468R

4 cyl Kubota diesel engine, 3 line, mounted on 1999 GMC truck with propane engine, welder, 2 rear jacks, front jack removed (needs to be fixed), 6” tools, drill stems, bits, etc  Price:  $40,000 PRICE REDUCED:  $34,500 – Rhode Island


BUCYRUS ERIE 22W (Ref#235R) 

bucyrus erie 22w

Manufactured 1950’s, front and rear hydraulic, hydraulic tool guide, freshly rebuilt lifting system including new cable, approx. 500’ of drilling line, 6 cylinder Continental gas engnine, good working main clutch and flat Kevlar belt, 23’ stem with closed rope socket, mixer sub, and 6” button bit, separate open side rope socket with rig, 2 BE stem wrenches, driving clamps, driving shoe, driving cap, like new spudding and lifting gears, mounted on 1969 Ford 850 tandem axle truck with V8 Ford engine (runs good), new 750 ci Edelbrock carburetor, all new light wiring, 10 900-20 ties, excellentshape (two steers need replaced), 5 x 3 transmission, differential lcoking rears, rear hitch and oilfield bumpers  Price:  $40,000 PRICE REDUCED: $38,500


BUCYRUS ERIE 22W  (Ref#11984) 

bucyrus erie 22w

3-line, International 4 cyl gas deck engine, mounted on 1972 GMC single axle truck w/V-8 350 hp motor, good condition, currently drilling, lots of tools 

Price:  $32,000 - Arkansas


BUCYRUS ERIE 22W (Ref#13988T)

Bucyrus Erie 22W

Completely rebuilt, new cables, 3 cyl Lister diesel deck engine, 3 line machine, mounted on 1980 International single axle truck with diesel engine, brand new drill bar, tooled up for 6” & larger holes, 3 hydraulic leveling jacks & additional stabilizing jacks, ready to go  Price:  $59,500 USD - Canada


BUCYRUS ERIE 21W (Ref#11391R)

bucyrus erie 21w

4 cyl Hercules gas deck engine, mounted on 1972 GMC single axle truck with gas engine, 2 line machine, 220 gallon water tank with pump, Lincoln welder, torches, toolboxes, 1 front & 2 rear mechanical leveling jacks, tooled up for 4” holes, 4” casing bumper, 4” drilling rod, 4” bailer, 500’ of 5/8” cable, extra parts for rig included, needs 3 new batteries, rear caliber leaking  Price “as is”:  $27,500  – Florida


BUCYRUS ERIE 21W  (Ref#6537Tb) 

Ford 172 deck engine, mounted on 1955 International truck with 501 engine, 2 line machine, 250’ main line 

Price reduced: $18,500 - Maine


BUCYRUS ERIE 20W (Ref#14815R)

bucyrus erie 20w

2 line machine, Allis Chalmers 4 cyl gas deck engine, mounted on late 1980’s single axle Ford Louisville with gas engine, telescoping mast, 2 rear screw jacks, tooled up for 6”  Price on Request – Canada


BUCYRUS ERIE 20W  (Ref#13127T

2 line machine, 40’ mast, munted on mid 1970’s International single axle truck with Cummins engine, Hercules gas deck engine, fully tooled for 5”, 1 front and 2 rear hydraulic jacks, currently working  Price:  $32,000 - Ohio


BUCYRUS ERIE 20W  (Ref#9270T

Peterson 3 cyl diesel deck engine, 3 line machine, new cble, mounted on 1999 International 4700 truck with 466 diesel engine  Price:  $20,000


BUCYRUS ERIE 20W  (Ref#6592Ta) 

4 cyl Hercules engine, 3 line machine, mounted on 2002 GMC truck with 350 gas engine  Price:  $25,000


BUCYRUS ERIE 20W  (Ref#7366T) 

2 lines, 4 cyl Hercules on deck, mounted on 2006 Freightliner truck, 4 speed automatic with overdrive, Cat C7 Acert in truck, 2 heavy duty hand jacks on back of truck, LED worklights, 400’ drill line, 400’ bailer liner, completely tooled 5-1/2” – 8-1/4” bits, set of breakout wrenches, misc tools and parts  Price:  $79,500


BUCYRUS ERIE 20W  (Ref#1534R) 

bucyrus erie 20w

Manufactured 1954, 3 lines, tooled for 3” and 4”, 400’ of 5/8” cable, 132 Ford engine on deck, mounted on 1973 Ford F600 truck with gas engine, tools  Price:  $19,500 - Minnesota


BUYCRUS ERIE 20W  (Ref#5739T

4 cyl Hercules deck engine, mounted on 1984 Ford single axle truck, diesel engine, 3 line machine, 500-600’ main line  Price:  $19,500


BUCYRUS ERIE 20W (Ref#5601RA) 3 line machine, Ford 172 deck engine, 2 part mast, mounted on 1974 GMC single axle truck with 350 V8 gas engine, drilling bar, 600’ of 5/8” cable, 2 rear mechanical jacks, tooled up for 6”, sitting a long time  Price:  $15,000 – Connecticut


BUCYRUS ERIE 20W  (Ref#4700Ra)

 bucyrus erie 20w

Manufactured 1963, John Deere 4 cyl disel on deck (new), 3 lines, mounted on Ford F700 truck with gas engine, 3” and 6” tools, assorted bits  Price:  $23,500


BUCYRUS ERIE 20W (Ref#13415R)

bucyrus erie 20w

3 line machine, gas deck engine, mounted on 2000 GMC with diesel engine, tooled up for 4”, 4 hydraulic leveling jacks, sitting a few years  Price:  $19,500


BUCYRUS ERIE 20W (Ref#13545RA)

Gas deck engine, 2 line machine, mounted on Diamond Rio with gas engine, well maintained, running condition, all tools & many extras  Price:  $28,500 PRICE REDUCED: $25,000 – Pennsylvania


BUCYRUS ERIE 20W  (Ref#5520R) 

bucyrus erie 20w

trailer mounted, 3 lines, manufactured mid 1970’s, Murphy air cooled diesel engine, tool with 4” tooling, one owner 

Price:  $30,000 PRICE REDUCED: $29,500


BUCYRUS ERIE 20W (Ref#8009N)

bucyrus erie 20w

Ford 4 cylinder gas deck engine, mounted on 1974 International 1800 with 345 gas engine, 3 line machine, 2 rear mechanical leveling jacks 

Price:  $29,500 – Minnesota
4” 6” & 8” tooling available at extra cost


BUCYRUS ERIE 1W  (Ref#12427Nb

Mounted on 1988 Chevy 1 ton truck, 2 lines, gas engine on deck, 2 rear hydraulic leveling jacks, dump bed, 30’ mast, tooled for 4”, stored inside, sitting 2-3 years  Price:  $16,000  PRICE REDUCED:  $11,500 – Indiana


BUCYRUS ERIE 1W  (Ref#4631R

2 line machine (mainline and sandline), Ford Industrial 4 cyl gas deck engine, hydraulic spudding arm, hyd tilt bed, hyd rear jacks and breakout wrench, mounted on 1975 Chevy C60 truck with 427 V8 engine, (truck does no start) set up as a jetting rig with centrifugal pump (powered by rig engine), 500# weight for driving 4” casing.  Truck and rig has not run since 1999.    Price:  $7,000 - Indiana


WALKER-NEER S33A  (Ref#6717R

walker neer s33a

rated 5500’ and has drilled to 6300’, 1500’ of drill line, 3000’ of sandline, 400’ casing line, McKissick blocks, can string with 6 lines (has 4 lines now), skid mounted, double pole, triple drum, 145 Waukesha engine (brand new only drilled 4-5 wells), completely rebuilt 1981, air clutches, (2) catheads, Rig with doghouse, floor and 5” to 20” tools 

Price: $85,000 PRICE REDUCED: $65,000


WALKER NEER C33A  (Ref#14459T

walker neer c33a

4500’ of 7/8” block line, 9/16” sandline, 3 McKissick sheaves, air clutches and controls, mounted on 1961 Mack truck with 250 hp Cummins engine, older rig but runs good  Price:  $75,000


WALKER NEER 32 SPECIAL  (Ref#1923N

Walker Neer 32 Special

Manufactured 1953, 140 Waukesha engine, mounted on double axle trailer, 2 lines (drill line, sand line), double pole, friction clutches, some 4-1/2” tools included 

Price:  $60,000 - Price Reduced: $39,500


WALKER NEER WS-31 (Ref#8606RA)

walker-neer ws31

Diesel deck engine, mounted on Army 6 wheel drive with gas engine, 40’ mast, 3 line machine, 4 rear screw jacks, 6” 8” 10” bits  Price:  $50,000  – New Mexico


WALKER NEER WS-31  (Ref#6352T

Manufactured 1987, 4 cyl Hercules deck engine, mounted on International Loadstar, 315 International truck engine, 3 line machine, 900’ main line, 1200’ sandlne, 200’ utility, (5) 16” drill bits, jars, drill subs, bailers, etc  Price:  $50,000


WALKER NEER WS-31  (Ref#743N) 

walker neer ws31

propane deck engine, mounted on 1963 Chevy tandem axle truck with gas engine, walking beams rebuilt, fully tooled 5” up to 12”, bits, bailers, etc, operating condition 

Price:  $29,000 Price Reduced $22,500- Idaho

 


CYCLONE 42 (Ref#3338R)

cyclone 42

4 cylinder Continental gas/propane deck engine, mounted on 1979 Ford F800 (not 4x4) with gas engine, telescoping mast, 3 line machine, 1000' of 1/2" on spool, fully tooled, ready to go 

Price:  $25,000PRICE REDUCED: $13,500 Pennsylvania


CYCLONE 42  (Ref#8224Ra) 

cyclone 42

Manufactured 1956, mounted on 1968 Chevy truck, includes stem, bailer, J wrenches, spare bits, needs work  Price:  $9,500

CYCLONE 40  (Ref#8224Rb

cyclone 40

Manufactured 1961, mounted on 1972 Ford truck, includes stem, bailer, J wrenches, spare bits, working condition  Price:  $15,000

PACKAGE PRICE FOR BOTH RIGS: $19,500


CYCLONE 36  (Ref#4791N

Manufactured 1964, Ford 300 6-cyl on deck, mounted on 1975 International truck with DT466 diesel engine, 36’ mast, 3 lines, 500’ of ¾” drilling line (new), 500’ sandline (new), 150’ casing line (new), hydraulic jacks, 6” string of tools  Price:  $19,500


ALTEN 32A  (Ref#12490) 

alten 32a

next heavier than 22W, new jack shaft, drill gear, clutches with ball throw out bearings, 4 hydraulic jacks, weighted walking beam platform for driller, 52’ derrick with 22 Walker-Neer shocks, 2 part casing line, elevator, 4 cyl Ford D172 rig engine with 4 sp transmission, new 7V power belt, mounted on 1970 6x6 multi-fuel truck,  new 30’ 5” tools with button bit and mixing bar, 20’ 4” bailer (dart) 

Price:  $80,000  Price Reduced: $59,500 - Michigan


ALTEN 24-A (Ref#12489) 

alten 24a

Similar to 22W, mechanically perfect, main gear has always been covered, shows little to no wear, main shaft, twin disc clutches, roller main bearing, ball throw out bearings, 52’ derrick with 20 new 20W shocks, pulleys all anti-friction, derrick tips up by hydraulic, elevator to about 25’, 162 in Continental with 4 sp transmission, new 5 v 1 piece power belt, main big pulley has added weight for fly wheel drilling effect, walking beam weighted, mounted on 1983 AM Generator Army truck truck with Cat diesel engine, Allison transmission, 6000 miles on truck, new carb, dist, and valve job, new tires, 10 sp Road Ranger transmission, air brakes, power steering, new tools 30’ overall with button bit and mixing bar, 20’ dart dialer (4” wells), driller’s platform 

Price:  $74,500 - Michigan


IDECO 10 CABLE TOOL RIG (Ref#11833R)

4 cyl Continental gas deck engine, mounted on 1961 International single axle truck with gas engine, 2 line machine, 30’ mast, no leveling jacks, 6” & 8” tooling, currently drilling  Price:  $16,500 – Utah


SPEEDSTAR 240 (Ref#1567R)

Manufactured 1946, 2 line machine, gas deck engine, 32’ mast, mounted on 1973 International with 345 gas engine, power swivel, 2 rear screw jacks, 3” & 4” tools, sitting a long time  Price:  $16,500  – Michigan


SPEEDSTAR 72  (Ref#3866R

3 line machine, 6 cylinder gas deck engine (rebuilt 5 years ago – 2 wells drilled since), mounted on Peterbilt cab over truck with diesel engine, 1 set of drill tools  Price:  $46,500


SPEEDSTAR 72  (Ref#4194R) 

Mounted on tandem axle disel truck, 3 line machine, tooling  Price:  $25,000 - Pennsylvania


SPEEDSTAR 72  (Ref#9349) 

speedstar 72

3 drum, auto braces, hydraulic levelers, 6 cyl Continenetal engine, mounted on International tandem axle truck, air brakes, good condition when parks, sitting 10 years  Price:  $39,000  PRICE REDUCED:  $29,500 - Pennsylvania


SPEEDSTAR 72 (Ref#7893R)

speedstar 72

4 cyl gas deck engine, mounted on 3 axle Military truck with gas engine, 3 line machine, all drill stems, fishing tools, bailers, etc, set up for 6” – 12”, 3 mechanical jacks available  Price:  $50,000 – California


SPEEDSTAR 71  (Ref#6537Ta

Manufactured 1971, gas red seal deck engine, mounted on 1984 GMC Kodiak truck with Cat 3208 diesel engine, 3 lines, hyd rear jack, clutch driven winch 

Price reduced: $19,500  -  Maine


SPEEDSTAR 71  (Ref#2669T

4 cyl Continental Red Seal engine, ¾” dril line, 5/8” sandline, ½” bailing line, lift line, set up for 4” tool, truck no good (will remove from truck)  Price $15,000 - Georgia


SPEEDSTAR 71 (Ref#2258TB) 3 line machine, standard mast, gas deck engine, mounted on 1989 Ford F600 2 wheel drive with diesel engine, driller & helper’s platforms, 2 rear hydraulic leveling jacks - California
Price:  $46,500 rig only
Price, fully tooled:  $53,500


Speedstar 71 (Ref#8661R)

Manufactured 1986, like new condition, Perkins 4 cylinder diesel deck engine, mounted on 1993 Ford L8000, 4 hydraulic leveling jacks, ready to go  Price:  $44,000 - Ohio


SPEEDSTAR 71  (Ref#6255R) 

Mounted on 1970’s International truck with gas engine, 3 lines, 4” tools, 6” bit, sitting a few years  Price:  $20,000 - Pennsylvania


SPEEDSTAR 71 (Ref#5482RB) 

3 line machine, Perkins diesel deck engine, mounted on 1980 GMC single axle truck, 4 screw jacks, 6” tools Price:  $28,500 – New York


SPEEDSTAR 71 (Ref#6075N

Manufactured 1985, Perkins diesel deck engine, mounted on Chevy single axle truck with 350 gas engine, 42’ telescoping mast, ¾” cable, 4 mechanical jacks  Price:  $45,000 - Pennsylvania


SPEEDSTAR 71   (Ref#2675N) 

speedstar 71 

Manufactured 1943, completely rebuilt, 3 cylinder Deutz diesel deck engine, oversized bull gear shaft with custom bearings, mounted on 1976 GMC with 366 gas engine, 3 line machine, hydraulic winch, 40’ hydraulic raised fixed mast, hydraulic breakout cylinder, drillers platform, 3 hydraulic 4’ leveling jacks, bailers, subs, pipe, all tools, complete and ready to go 

Price:  $35,000  PRICE REDUCED:  $27,500 - Maine


SPEEDSTAR 55 (Ref#10794R)

speedstar 71

Trailer mounted with propane engine, 30’ mast, 3 line machine, 4 mechanical jacks, includes 6” & 8” bits with stems, set of jars & wrenches  Price:  $19,500 – Idaho


SPEEDSTAR 55  (Ref#15207T) 

speedstar 55 speedstar 55

Ford Industrial V6 deck engine, mounted on 1969 GMC 2-ton ruck with 350 Chevy engine, mainline, sandline, bailing line, 36’ mast  Price:  $14,500


KEYSTONE 55 CABLE TOOL RIG (Ref#7341R)

keystone 55

Manufactured 1957, Ford 4 cyl ind gas deck engine, 2 line machine (3rd line avail) mounted on 1979 GMC C70 with gas engine, 1 stage hydraulically raised derrick, 3 hydraulic leveling jacks and 2 center outriggers, tooled up for 6” wells 

Price:  $32,500  PRICE REDUCED:  $27,500  – Maine


KEYSTONE 50  (Ref#6774N) 

keystone 50

Ford 196 cu in gas engine on deck (excellent), mounted on GMC tandem axle truck with GMC gas engine, 5 hydraulic leveling jacks, boom lifts and extends hydraulically, 3 line machine, 2 line operates mechanically, 3rd line is hydraulic, 6” and 8” tools  Price:  $35,000  PRICE REDUCED:  $27,500 - Pennsylvania