Last Updated: 03/15/2024 10:33 AM

Swab Rigs

Pulling Units, Pump Hoists

 

G & R pump hoists 1200, 500, 400
Hunke/Smeal R30, 12T, 12R, 10T, 8T, 6T, 5T, 4T, 3T
Ideco H37E
Jessen/Monitor pump hoists
Kyle pump hoist 12K
Monitor/Jessen pump hoists
Pulstar P38000, P29000, P20000, P12000, P10000, P7000, P4000
Reichdrill Eagle
Semco   S25000, 15000, S8000, S6000 
Smeal/Hunke 12T, 12R, 10T, 8T, 6T, 5T, 4T, 3T
Walker Neer pulling units
Cyclone pump hoist/swab rigs

SWAB RIGS

SWABMASTER SWAB UNIT  (Ref#3823Ta)  Mounted on 2009 International 7400 SBA 4 x 2 truck, 84,000 miles, 3,698 hours, lubricators, oil savers and mandrils, rig will hold up to 18,000’ of line, ¼” diameter of braided line, 38,000 lbs operating mast when properly guided  Price:  $197,500

SWABMASTER SWAB UNIT  (Ref#3823Tb)  Mounted on 2008 International 7400 SBA 4 x 2 truck, lubricators, oil savers and mandrils, rig will hold up to 18,000’ of line, ¼” diameter of braided line, 38,000 lbs operating mast when properly guided     Price:  $182,500

FALCON SWAB RIG  (Ref#7494T)  Cummins diesel engine on deck, mounted on Mack truck with Mack diesel engine, holds 11,000’ of cable, walking beam, hydraulic extendible mast, sitting since 2023  Price on Request

DA MFG MODEL 280 SWAB RIG  (Ref#4163T)  Mechanical drawworks, holds 10,500’ of 9/16 swedge line, Mounted on 2007 International truck with extended cab 7400, DT570 engine, 37,744 km, 2796 hours  Price:  $118,500 USD

2008 STERLING PUMP HOIST/WATER TRUCK  (Ref#3571T)  40,000# capacity, 47’ hydraulically raised boom rated at 20,000# static with Braden hydraulic winch, 8000 jib electric winch, mounted on 2008 Sterling LT9500 truck (20,000 kms), p/b Cat C13 diesel engine, 6 speed Allison automatic transmission, PTO, air ride suspension, steel flatbed with 1400 gallon water tank, 3’ X 9”H side rails, hydraulic pipe clamp, hydraulic outriggers, breakout and spinner controls, wireless remote  Price:  $115,000

STELLAR 6628 CRANE/PUMP HOIST  (Ref#275T)  Lifting capacities: 2925 lbs @ 13’, 1350 lbs @ 28’, mounted on single axle 2002 International truck, toolboxes  Price:  $52,500

PULLING UNIT  (Ref#10917Tb)  double drum, 40’ mast, mounted on International 4700 tandem axle truck, has pulled 1000’ of 8” casing (filled with water), tooling  Price:  $55,000

SHOP BUILT CABLE TOOL/SWAB RIG  (Ref#10188)  triple drum, friction clutch, cathead (sandline holds 2400’ of 5/8” line), mounted on tandem axle Chevy truck with 427 gasoline engine, 8-5/8” x 45’ single pole, new tires, power steering, wireline unit, good usable rig for shallow oil/gas lease, drills, workover, swab capabilities, no tools  Price:  $112,500 - Oklahoma

1995 KENWORTH T800 SWAB RIG  (Ref#2550Ta) Pole rig, Franks drawworks, holds 16000’ of sandline, no cable, no tools, last worked 2021  Price:  $47,500

1991 INTERNATIONAL MODEL 8000 SWAB RIG  (Ref#2550Tb)  Wilson drawworks, 45' scope derrick, no cable, last worked December 2019  Price:  $83,500

1992 MACK RD600 SWAB RIG  (Ref#2550Tc)  Wilson drawworks, 9000' cable, 35' derrick (derrick replaced 2017)  Price:  $113,500

1994 INTERNATIONAL MODEL 8100 SWAB RIG  (Ref#2550Td)  Franks drawworks, 9,000’ of 9/16” cable (may need splice job soon) bottom part of spool still in good shape, 35’ derrick, travelling sheave, tooled up, recently put new flywheel on rig and new rear end, currently working  Price:  $72,500

2002 MACK RD600 SWAB RIG  (Ref#2550Tf)  Wilson drawworks, Detroit engine on deck, 40’ derrick,  no line (can fit 14,000’ of 9/16”, no tools, parked since 2021, back radiator on Detroit needs a little work (has a small hole), hydraulics need fix on the pump (leak), other than that working condition Price:  $57,500

1971 INTERNATIONAL MODEL 4370 SWAB RIG  (Ref#2550Tg)  Franks drawworks, 11,000' of 9/16" cable (will hold 16,000'), 35' derrick  Price:  $63,500

SLICK LINE UNIT  (Ref#2560T)  2006 Ford F550, you can operate it from the inside, last worked 2020, needs new wire, crane needs maintenance  Price:  $47,500

1999 DODGE SLICK LINE UNIT  (Ref#2550Th)  5 speed, Slick line equipment built 2017, tool  Price:  $72,500

2007 DODGE SLICK LINE UNIT  (Ref#2550Tj)  Cummins engine, 6 speed, Slick line equipment built 2018, tools  Price:  $92,500

1979 MACK SWAB RIG  (Ref#2970Ta)  Needs to be mounted on newer truck Price:  $26,500

FRANKS 658 SWAB RIG  (Ref#9037Ta)  Built 1977, Pemco 45-30 mast 45' clear height x 30,000#, 9/16" swabline, mounted on 3 axle carrier with 6V71 Detroit diesel, Allison 446-2 transmission (has problem, and have new spare), Franks 658 drawworks  Price:  $147,500

SKYTOP BREWSTER SWAB RIG  (Ref#8491T)  Mounted on 3 axle Crane Carrier, 45’ mast, drawworks has 9” brakes, Detroit 8V engine (runs very well), hydraulic system functions well, oil saver, swabbing mandril  Price:  $72,500

SKYTOP SWAB RIG  (Ref#9037Tc)  Built 1977, Detroit diesel, 54,000 GVW, needs work  Price:  $50,000

SKYTOP SWAB RIG  (Ref#4710Td)  Single drum drawworks, 55’ mast, mounted on Kenworth T600 with Detroit 60 Series engine, holds 14,500’ of 9/16” line  Price on Request
Also available:  Trailer mounted 120-140 bbl fiberglass tank

SWAB RIG  (Ref#8055T)  Detroit 8V71 engine, 15,000' of 9/16" line, mounted on 3 axle carrier  Price:  $138,500

TCB WELDING SWAB UNIT  (Ref#11549Td)  2014 International truck, single drum, 44' derrick, 20,000# hook load, 8,000# hook load slant  Price:  $310,000 USD

TCB SWAB RIG MODEL TCB-44-30S  (Ref#4118T)  Built 2008, 44' working height, mounted on International 7500 truck, 30,000# single line pull derrick, max hook load vertical 30,000#, maximum hook load slant 8,000#, holds 14,000' of 1/2" swedge line, Allison transmission, DT570 engine in truck, includes lubricator, saverhead, and ratigan BOP  Price:  $195,000 CDN

SWAB RIG  (Ref#7353Tb)  28' hydraulically rasied derrick, 9200' of 4/8" stainless sandline, 5 cylinder Mereces diesel engine, mounted on 1986 Chevy C70 single axle truck with 502 gas engine, hydraulic leveling jacks in rear  Price:  $52,500

SWAB UNIT  (Ref#11549Te)  2013 Mack Granite tri-drive truck, 4000 hours, 48' derrick, drawworks drum will hold 14,000' of-1/2" line, fully hydraulic unit, slant capable, DEF System deleted  Price:  $345,000

SWAB RIG  (Ref#4710Tc)  Single drum drawworks, 55’ mast, mounted on 1995 Kenworth truck with Cummins 350 engine, 55’ mast, 14,500’ of 9/16” capacity, toolbox, good clean condition  Price on Request
Also available:  Trailer mounted 120-140 bbl fiberglass tank

MOELLER SWAB UNIT  (Ref#9241R)  Manufactured 1982, single drum, 42' mast, drum holds 18,000' of 9/16" sandline, Mesa drawworks, V8 Detroit engine, Rigtech carrier, sitting since 2016  PRICE:  $42,500

MOELLER SWAB RIG  (Ref#7324T)  Mounted on 1999 International truck with diesel engine, PTO, Moeller single drum drawworks, 9/16” sandline, sitting since 2020  Price:  $62,500

MOELLER SWAB UNIT  (Ref#6061Ta)  Built 1980, Detroit engine, automatic transmission, runs good, needs line, will hold 15,000'  Price:  $94,500

MOELLER SWAB RIG  (Ref#4710Tb)  Moeller single drum drawworks, 55’ mast, 14,500’ of 9/16” line capacity, mounted on 2003 Kenworth T800 truck, approx 100,000 miles, 2 leveling jacks,  toolbox, well tooled  Price on Request
Also available:  Trailer mounted 120-140 bbl fiberglass tank

PUMA WELL SERVICE SWAB RIG  (Ref#7442Ta)  Manufactured 2004, mounted on 2004 International truck with diesel en gine, 50' derrick, 2000 hrs on engine, located Canada  Price:  $60,000 USD
Price unmounted (without truck):  $40,000 USD

HIGH CALIBER WELDING SWAB RIG  (Ref#7442Tb)  Manufactured 2004, unmounted, large drum, located Canada  Price:  $29,500 USD

MESA SWAB RIG  (Ref#15642T)  mounted on 2001 Mack tandem axle truck with Mack diesel engine, right angle gearbox, 13 speed transmission, Mesa drawworks holds 20,000' of 9/16" sandline, currently has 17,000' on it, hydraulically operated operator's platform, two hydraulic jacks in front and two in rear,  ready to work, tires good  Price:  $144,500

MESA SWAB UNIT (Ref#8271Ta)  Ready to work, mounted on 1985 Peterbilt truck with Cummins NCT engine, PTO, single drum, complete with tools  Price:  $54,500

RIGTECH SWAB RIG  (Ref#579T)  Built 2006, 45' derrick, Wilson single drum will hold 17,000' of 9/16" sandline, no line on rig, mounted on 2000 International tandem axle truck with Detroit 60 Series, Allison auto transmission, right angle drive  Price:  $43,500

FRANKS 658 SWAB RIG  (Ref#3330Ta)  new derrick, mounted on 1986 Peterbilt truck , 350 hp Turbo Cummins  Price:  $94,500

FRANKS 200 SWAB RIG  (Ref#7275T)  53' mast, Detroit 6V71N engine, Allison transmission, 160 sand drum with 15" double roto hydromatic, new 9/16" line, 14,000' sandline (can hold 16,500')  Price:  $162,500

WILSON SWAB RIG  (Ref#3330Tb)  mounted on 2001 Freightlinter truck, Detroit Series 50 turbo engine  Price:  $94,500

WILSON MOGUL 42 SWAB RIG  (Ref#6061Tb)  Mounted on Ford 8000 truck, Detroit 6 engine, splitter box, will hold 15,000' (now has approx 5000')  Price:  $94,500

WILSON WORKOVER SWAB RIG  (Ref#13398R)  Double drum Wilson Sr and Wilson JR drawworks,  sandline capacity 10000' of 3/16", mounted on tandem axle, 1987 Freightliner tandem axle truck powered by Detroit diesel engine, 2 hydraulic leveling jacks, Detroit diesel on deck, 50' hydraulically raised mast, brand new hydraulic cylinder just replaced for lifting derrick, has pulled a minimum of 3000' wells, all new hydraulics,     PRICE:  $147,500

IDECO SWAB RIG  (Ref#3330Tc)  Mounted on Corevan, 6 speed auto transmission, Detroit 8V92  Price:  $189,500

HOPPER SWAB RIG  (Ref#3330Te)  mounted on 2005 Freightliner with Detroit 60 Series engine  Price:  $189,500

COOPER SWAB RIG  (Ref#4710Ta)  Cooper 550 single drum drawworks, 12” brake, 55’ mast, 15,500’ of 9/16” line capacity, mounted on 1996 Kenworth T400 truck with Cummins 350 hp engine, 10 speed transmission, 2 hydraulic leveling jacks, approx 100,000 miles, well tooled  Price on Request
Also available:  Trailer mounted 120-140 bbl fiberglass tank

COOPER SWAB UNIT  (Ref#1464T)  Manufactured 1978, rebuilt 2006, mounted on 1999 Freightliner single telescopic mast, max pull on push load 43,000#, weight indicator, dual tandem drive axles, 8000' – 10,000' of 9/16" swab line, Detroit Series 50 diesel engine, Allison auto transmission, 198,000 miles  Price:  $172,500

COOPER SWAB RIG  (Ref#7959Ta)  Cooper drawworks, Detroit 6V71 deck engine, 45’ mast, 14,500’ of 9/16” sandline, mounted on 1978 Freightliner truck with Cat 3406 engine, some tools, ready to work  Price:  $87,500

COOPER SWAB RIG  (Ref#3912R)  needs rebuilding, Cummins N14 engine on deck, 500 hp right angle drive, sandline, mounted on 1991 Freightliner truck with Cummins engine, holds 16,000' of 9/16" capacity, air over friction, traveling crown sheave, 60' from ground to corwn when erect, hydraulic raising, toolboxes, belly pans and drip guards, 43'L x 8'W x 12'6" H, 70,000 lbs, sitting for many years    PRICE:  $27,500

WEINS (SIMILAR TO COOPER) SWAB RIG  (Ref#3330Td)  Newer drawworks, mounted on 2002 Mack truck with Mack Turbo diesel  Price:  $189,500

CARDWELL H  (Ref#986N)  double drum workover and cable tool rig, mounted on tandem axle trailer, 1800' sandline with about 4,000' of new line on a spool, new block, doghouse on trailer, 6 cylinder Hercules deck engine propane, 55' pole with 3 settings 42', 48' and 55', (3) 15 ton manual jacks, 20' stem and jars, elevators, bails, boomers, tubing group slip, quick hitch block, (2) breakout tongs, tubing tong, rod wrenches, cable line cutter, 30' bailer  Price:  $55,000

SWAB RIG  (Ref#351N)  Mounted on 1993 Peterbilt truck with 22.5 tires and powered by Cummins L14 diesel engine, 4 hyd leveling jacks, 471 Detroit, Automatic transmission, 45' mast, 1600' swab line, weight 46,000#,, tooled    PRICE:  $95,500

1990 KENWORTH SWAB RIG  (Ref#2411Tc)  Will hold 16,500' of 9/16" sandline, right angle drive, 8 speed Eaton standard transmission, enclosed operators cab with heat and A/C, tooled, ready to work  Price:  $190,000

SKID MOUNTED SPOOLER  (Ref#4710Te)  Franks drawworks, diesel engine  Price: $19,500

NEW HYDRAULIC SWAB UNITS  (Ref#11777R)  30,000' of ¼" camesa dycam swab line, fully tooled, hydraulic leveling jacks, Roadpower generator, rooftop AC, 51' 35,000 masts or pole mast, Geo-log weight indicator and measuring heads, no truck (you provide truck)  Price:  $288,000

SWAB UNIT (Ref#11549Ta)  2006 Sterling swab truck, 42 x 10 drawworks, 4200m (13,700') new-1/2" line, 46' derrick, 2 winches, Cat C13 (410 hp) engine, Alliston automatic transmission, approx. 10,000 hours, right angle drive in out of unit  Price:  $199,000 USD

SWAB UNIT  (Ref#11549Tb)  2008 International 7400 Series truck, 14,000# front axle, 40,000# rear axle, 8865 hours, air ride suspension, 47' ground to crown working height derrick, 18,000# single line pull derrick, 12,000' capacity drawworks, air disc brakes, and line spooler, rear operators cab and front walk in toolbox, electronic weight indicator, rear depth meter, air actuated derrick locks, air operated lubricator locks, 2 hydraulic aux winches 2000# pull, 2 tool boxes and working rear floor, emergency shut off front and rear, pre heater, tubing and casing lubricator, tools, new derrick and jack rams, new derrick pins and derrick ears reworked, new drawworks chains and bearings  Price:  $164,500 USD

SWAB UNIT  (Ref#11549Tc)  2010 International 7400 Sereis truck, 14,000# front axle, 40,000# rear axle, 6061hours, air ride suspension, 47' ground to crown working height derrick, 18,000# single line pull derrick, 12,000' capacity drawworks, air disc brakes, and line spooler, rear operators cab and front walk in toolbox, electronic weight indicator, rear depth meter, air actuated derrick locks, air operated lubricator locks, hydraulic auxiliary winch, 2 tool boxes and working rear floor, emergency shut off front and rear, pre heater, tubing and casing lubricators  Price:  200,000 USD

SWAB RIG  (Ref#9037Tb)  Pemco Model 45-30 mast 45' clear height x 30,000#, 9/16" swab line, mounted on 1977 International Transtar 4300 rebuilt engine, 3 axles, 44,300 GVW  Price:  $162,500

PUMP HOISTS/PULLING UNITS

NATIONAL OILWELL VARCO 2500' PULLING UNIT  (Ref#4198RB), National Oilwell Varco (DS) drawworks, 40' derrick (45' crown to ground), mounted on 1982 Ford 700 with Detroit V8 diesel engine, 11R22.5 tires (good shape), McKissick pulley, hydraulic leveling jacks front and rear,   Price:  $52,000

WILSON 2500' PULLING UNIT  (Ref#4198RC), Wilson drawworks with disc clutches, 5/8" high strength cable, 40' derrick (42' from crown to ground), 200hp GM diesel deck engine, mounted on 1986 International with V8 diesel engine, 10.00 20 solid tires (rear tires are new),   Price:  $52,000

CARDWELL 4000’ PULLING UNIT  (Ref#7683T)  In-line 6 cyl Ford gas deck engine, mounted on Ford 3WD truck with 7.3L diesel engine  Price:  $67,500

SINGLE POLE PULLING UNIT  (Ref#3785T)  Mounted on Ford truck, pole rebuilt, needs deck engine  Price:  $36,500

SHOP BUILT PUMP HOIST (Similar to Smeal 12T)  (Ref#2016Na)  mounted on 1984 Brigadier truck with 6V71 Detroit engine, PTO  Price:  $28,500

SHOP BUILT PUMP HOIST (Ref#908T)  Can pull up to 30,000#, Pony gas deck engine, 1500’ of 3/8” sandline, 400’ of ½” main line, mounted on 1974 Ford F600 2WD truck with gas engine, no remote, no tools, 2 rear manual jacks  Price:  $11,500

SHOP BUILT PUMP HOIST (Ref#8776R) mounted on 1992 Ford F600 with gas engine, large utility boxes, 35' mast, 8000# main winch, 1000# sandline set up with 300' of line for bailer, electric winch to load welder into front box, tools for up to 4" drop pipe & all hand tools  Price:  $40,000

SHOP BUILT PUMP HOIST  (Ref#9697T)  Mounted on 1989 Ford 1-ton truck with gas engine, remote control, toolboxes, no cathead, no sandline, 2 rear hyd leveling jacks, sitting 3 years  POR

SHOP BUILT PUMP HOIST (Similar to Smeal 3T)  (Ref#4554T)  Mounted on 1989 Ford Superduty 2 WD truck with diesel engine, PTO, 42' mast, no remote, no sandline, no cathead, toolboxes, 2 rear hydraulic leveling jacks  Price:  $22,000

PULLING UNIT  (Ref#9296T)  Failing drawworks, 1000’ – 1500’ depth, mounted on 1985 Chevy C10 truck with gas engine  Price:  $19,500

SHOP BUILT PUMP PULLER  (Ref#7381T)  electric engine, trailer mounted  Price:  $6,000

PUMP HOIST  (Ref#5242Ta)  Mounted on 1983 Chevy truck with gas engine, 2 rear jacks, starts and runs  Price:  $32,500

WELLMASTER BT-32B PUMP HOIST  (Ref#1718N)  Manufactured 2006, unmounted, 6,000# single line, 12,000# 2-part line, 18,000# 3-part line, 32' telescopic derrick  Price: $13,500

G & R PUMP HOIST  (Ref#3954T)  Manufactured 1990, 12,000 lb lift capacity, mounted on 990 Ford F450 truck with diesel engine, approx. 70,000 miles, one owner rig  Price:  $50,000

G & R 400 PUMP TRUCK   (Ref#6504T)  Mounted on 1986 International 1900 truck with 6.9L diesel engine, 24 cfm air compressor, walking beam, drive casing with 350# hammer, good for 2 – 4" well development, leak in hoist control valve  Price:  $22,000

G & R 1200 PUMP HOIST  (Ref#11060T)  Manufactured 1980, Mounted on 1984 Mack truck, Mack 300 hp diesel engine, new PTO, pump, cable, hyd valves, paint, pins, 5 speed, 167,000 miles, 36' mast, no sandline, no toolboxes, 2 rear jacks, pipe racks    PRICE:  $35,000

G & R PUMP HOIST  (Ref#6423T)  Unmounted, all standard features, sitting two years (running when parked)  Price:  $16,500

G & R PUMP HOIST  (Ref#3059T)  Manufactured 1984, mainline, sandline, mounted on 2000 International 4700 truck with DT466e, Eaton 7 speed manual transmission, approx. 415,000 miles (over 12,000 hours) on truck,   Price:  $48,500

NATIONAL 500C PUMP HOIST  (Ref#8353Tb)  Built 1998, mounted on 1998 Ford F800 truck, 60,000 miles, 6570 rig hours, (2) toolboxes,   Price:  $47,500

SWINGER PUMP HOIST  (Ref#13253Rb)  Manufactured 1989, no sandline, mounted on 1989 GMC 4 x 4 truck with gas engine, toolboxes, no tools, 2 rear jacks, new paint  Price:  $23,000

SWINGER MODEL 45 PUMP HOIST  (Ref#2245T)  Mounted on 2009 Ford 750 extended cab, 325 hp Cummins, 31,000 GVW, 2 wheel drive, locking rear end, manual transmission, air brakes, dual winches with 2 speed hydraulic motors, hydraulic wire winder, 4 leveling jacks, multiple toolboxes, 2 heavy duty pipe racks  Price:  $68,500

SWINGER PUMP HOIST  (Ref#3709T)  Built 1990, 3 ton, mounted on 1990 Ford F350 4WD truck, 4 speed with overdrive transmission, new clutch 2018, recently replaced 460 engine (low miles), 28’ extended boom, 4000# winch on main line, 2500# sandline, 4 hydraulic leveling jacks, pulling tools, 6” pipe with caps to carry drop pipe, 5500 Honeywell 220/110 generator wired into outlet on back of truck to test run pumps, starter box in wiring, holders for spools of wire and rope on back, 4” bailer, 2” bailer, well maintained, last worked 2020 but started occasionally   Price:  $31,500
Also available ¾ ton flat bed with toolboxes

SWINGER PUMP HOIST  (Ref#1304T)  unmounted  Price:  $16,500

KYLE 8K PUMP HOIST  (Ref#8788T)  Manufactured 2008, no sandline, mounted on 2008 Ford F550 4 x 4 truck with 6.4L Powerstroke diesel engine, 135,000 miles, 10' aluminum bed, aluminum toolboxes, remote, crane pedestal, hydraulic jacks  Price:  $85,000

KYLE 5K PUMP HOIST  (Ref#139T)  Manufactured 2012, wire winder, hydraulic to rear, mounted on 2012 Dodge Ram 4500 truck, 112,000 miles, open bed, storage  Price:  $108,000

CUSTOM BUILT WORKOVER RIG (Ref#13714RA) Manufactured 1960, 50 ton capacity, gas deck engine, mounted on 1960 Dodge with 318 ind engine, sitting 2 years  Price $21,500

SMEAL R12  (Ref#11072Tb)  Mounted on 2005 Ford F750 truck, Cat 3126 engine, sandline, tail out line, mainline, 30' mast  Price:  $163,500

SMEAL R12  (Ref#11072Tc)  Mounted on 2002 Ford F750 truck, Cat 3126 engine, sandline, tailout line, mainline, 30' mast  Price:  $152,500

SMEAL 12T  (Ref#11072Ta)  Mounted on 2004 Ford F750 truck with Cat 3126 engine, sandline, tail out line and main line, 30' mast  Price:  $133,500

SMEAL 12T PUMP HOIST  (Ref#3955T)  Manufactured 1980, diesel deck engine, sandline, breakout cathead, telescoping mast, no remote,  mounted on M9-32A2 5-ton military truck with diesel engine, Allison automatic transmission, 2 rear leveling jacks  Price:  $55,000

SMEAL 12T  (Ref#5660T)  Manufactured early to mid 1990's, bailline, sandline, swivel, blocks, no cathead, mounted on 1989 Ford 8000 tilt cab with 210 Turbo engine, 8000# winch, tools    PRICE:  $89,500

SMEAL 12T  (Ref#878T)  Manufactured 1977, mounted on 1977 Ford  Price:  $52,500

SMEAL 10T  (Ref#11694T)  No sandline, no cathead, has plug in for remote control, but does not have remote, standard mast, mounted on 1997 Peterbilt with Cat C7 engine, new hydraulic hoses, 2 rear leveling jacks, painted  PRICE:  $52,500

SMEAL 10T  (Ref#3173T)  Sandline, mounted on 1991 International 5300 truck with DT366 diesel, 70,000 miles, windmill extension, cathead, hydraulic oil cooler, breakout wrench, tailout winch, remote control, 2 rear jacks PRICE:  $62,500

SMEAL 10T  (Ref#2999N)  Rig manufactured 1970's, mounted on 2001 GMC truck with Cat V8 diesel engine, truck needs new fast idle, no air brakes, PTO, bailing drum, sandline, no remote (wired for remote), no cathead, no pipe or tools, all hydraulics gone through February 2014    PRICE:  $45,000

SMEAL 10T  (Ref#3302T)  Manufactured 1975, sandline, mounted on 2001 International truck with DT466 engine, manual 6 speed transmission, hyd brakes, 32,312 miles, all new hydraulics January 2017, new style one body control from Hunke, no remote, updated hydrraulic motors, set up for power tongs, 2 hyd tanks  PRICE:  $43,500

SMEAL 10T PUMP HOIST  (Ref#367T)  Manufactured 1975, mounted on 1975 Ford F600 with gas engine, new front tires, new brakes, windmill extension, sandline with 1000’ of ½” cable, cathead, breakout wrench, underdeck storage, chain wrenches, pipe wrenches, slings, elevators, bailer  Price:  $52,500

SMEAL 8T  (Ref#7937T)  Manufactured 1998, mounted on 1998 Ford F800 2WD with diesel engine, PTO, remote control, sandline, cathead, telescoping mast, toolboxes, 2 rear hydraulic leveling jacks Price on Request

SMEAL 8T  (Ref#72R)  Manufactured 1997, mounted on 1991 International truck, Cummins diesel, sandline and main drum, straight 6 Cummins engine, 10 speed transmission, utiity body, 40' extension mast, no cathead, remote control (needs new cable), 2 rear jacks, 5/8" cable on mainline    PRICE:  $45,000

SMEAL 8T (Ref#15589R) PTO, mounted on 1994 International single axle truck with DT466 engine (not 4x4), telescoping mast, remote control, sandline, toolboxes, 2 rear hydraulic leveling jacks, located Canada  Price $38,500 USD

SMEAL 8T  (Ref#7448T)  Mounted on 1987 Ford F450 2 wheel drive truck, 7.3L diesel engine, aluminum service body, toolboxes, remote control, sandline, hydraulic walking beam, 2 rear hydraulic jacks, standard mast  Price:  $47,500

SMEAL 8T  (Ref#12405T)  Built 1979, sandline, mounted on Ford Louisville truck with diesel engine, no remote, no cathead, toolboxes, 1 front and 2 rear hyd jacks  Price:  $32,500

SMEAL 8T PUMP HOIST  (Ref#12698T)  Unmounted, manufactured 1979, sandline, cathead, hoist only (truck not included) Price:  $39,500

HUNKE 6T PUMP HOIST  (Ref#9510T)  Manufactured 2017, mounted on 2017 Dodge Ram 5500 with Cummins 6.7L turbo diesel engine (approx. 47,000 miles), full lighting package, 2 manual tilt pipe racks, WeatherGuard toolboxes, no sandline, stored inside, excellent condition  corded remote  Price:  $126,500

SMEAL 6T  (Ref#15188T)  Manufactured 2013, mounted on 2013 Dodge 5500 4 x 4 truck, PTO, automatic transmission, cathead, wire spool brackets, two pipe racks (one is powered), rope sheave, available June 2023  Price:  $107,500

SMEAL 6T  (Ref#13706Ta)  Manufactured 2007, mounted on 2000 Ford F550 truck, 2 wheel drive with diesel engine, low miles, remote control, toolboxes, 2 rear hydraulic jacks, no cathead or sandline  POR

SMEAL 6T  (Ref#7819T)  Manufactured 2005, mounted on 2005 Ford F450 2-wheel drive truck with V10 gas engine, manual transmission, remote control, no sandline, 38' mast, toolboxes, 2 rear leveling jacks, stored inside  POR

SMEAL 6T PUMP HOIST  (Ref#1543T)  Built 2002, mounted on 2002 Ford 4 x 4 truck, 5 speed, 41,000 miles, 7.3L diesel engine, cord remote, new idle control, new cable, set up as single line, can use sandline, 34' mast, new tires, one owner  Price:  $82,500

HUNKE 6T PUMP HOIST  (Ref#1147Ta)  Manufactured 2013, mounted on 2001 Peterbilt truck with Cat C12 engine, PTO, 200,000 miles, 40’ boom, 14’ boom extension, remote, sandreel is power up and power down, 2 pipe racks   Price:  $87,500

SMEAL 6T PUMP HOIST  (Ref#997T)  Manufactured 2001, mounted on 2011 Dodge 4WD truck with Cummins engine, approx. 160,000 miles, main line, sandline, no remote, poly wheel on back, utility body, 2 rear hydraulic leveling jacks  Price:  $82,500

SMEAL 6T PUMP HOIST  (Ref#4829T)  Sandline with ¼” line, mounted on 2002 Sterling truck with Mercedes-Benz Model OM 906 LA engine with approx. 99,000 miles  Price:  $62,500

SMEAL 6T PUMP HOIST  (Ref#7629T)  Manufactured 2000, mounted on 1995 Ford F800 truck with 98000 miles, Cummins diesel engine, Alliston automatic transmission, 46’ extended boom, no sandline  Price:  $55,000

SMEAL 6T PUMP HOIST  (Ref#109T)  Manufactured 2000, sandline, mounted on Ford F550 (not 4wd), 7.3 diesel engine, standard transmission, approx. 130,000 miles, clean condition  Price:  $72,500

HUNKE 5T PUMP HOIST  (Ref#5246T)  Manufactured 2017, mounted on 2017 Ford F450 2WD truck, approx. 142,100 miles, 6.7L diesel engine, control levers outside the cage, dual pipe racks, wireless remote, 2 speed winch, 9’ Dakota utility body with top boxes  Price:  $110,000

SMEAL 5T PUMP HOIST  (Ref#9426T)  Mounted on 2022 Ford F450 2WD truck with diesel engine, PTO, 10 speed automatic transmission, 7800 miles, wireless remote control, no cathead, sandline available (not on hoist now, but included), 38’ telescoping mast, new hydraulic hoses, speed control, 2 rear hydraulic leveling jacks  Price:  $122,500

SMEAL 5T PUMP HOIST  (Ref#7656T)  Manufactured 2006, remanufactured 2023, mounted on 2017 Ford F450 truck, 177,000 miles, tilt rack on passenger side, front jack, work lights, 9’ box  Price:  $95,000

SMEAL 5T PUMP HOIST  (Ref#9613T)  Manufactured 2014, 2 line machine, sandline, 20’ mast, mounted on 2014 Ford F550 4x2 with 6.7L Power Stroke V8 diesel engine, 6 speed automatic transmission, 143,832 miles  Price:  $77,500

HUNKE 5T PUMP HOIST  (Ref#9804T)  Mounted on 2012 Dodge Ram 4500 2-wheel drive truck, no sandline, 1 line machine, no remote, 2 rear jacks  Price on Request

SMEAL 5T PUMP HOIST  (Ref#12418T)  Manufactured 2008, on  a 9’ RKI utility body, mounted on 2008 Ford F450 4 x 4, 6.4L V8 diesel engine, 6 sp transmission, 168,000 miles, new engine, DPF installed 2021, (2) 16’ pipe racks, corded remote, welder, generator  Price:  $70,000

SMEAL 5T PUMP HOIST  (Ref#9162T)  Rebuilt with new hydraulics, new sandline, all new cables,  cylinder leaks repaired, 3 cylinder Kohler diesel deck engine, mounted on 2011 Ford F550 4x4 truck with 6.7L Powerstroke diesel engine  Price:  $54,500

SMEAL 5T  (Ref#5914T)  Manufactured 2007, mounted on 2007 Ford F450 truck, 228,220 miles, hydraulic leaks onmain mast, currently California compliant until 2021  Price:  $36,500

SMEAL 5T PUMP HOIST  (Ref#7620T)  Manufactured 2006, single drum, drum on back for spooling hose and wire, toolboxes, headache racks, mounted on 2003 Ford F550 4 x 4 dually truck with 6 liter diesel engine, new emergency brake, recently overhauled, includes pitless adapter tools  Price:  $45,500 USD

SMEAL 5T  (Ref#13272T)  Mounted on 2006 Ford F550 truck with diesel engine, 155,000 miles, new injector and high pressure pump, 36' mast, mainline, sandline, 2 pipe racks, new tires, service body, storage  Price:  $47,500

SMEAL 5T HRG PUMP HOIST  (Ref#279T)  Manufactured 1988, mounted on 2009 Sterling Bullet 5500 4 x 4 truck, 42,300 miles, Cummins diesel engine, 4642 engine hours, aluminum utility bed  Price:  $59,000

SMEAL 5T PUMP HOIST  (Ref#4224T)  Hoist manufactured late 1980’s, 2 lines, mainline and sandline, 500’ of domestic 3/8” cable on sandline, mounted on 2007 Dodge Ram 3500 4 x 4 truck with 6.7 Cummins engine, 6 speed transmission, PTO, no remote, 2 rear hydraulic leveling jacks. Tooled with 2 screen bailers, 1” 1.25” and 2” pipe elevators, misc tools for 4” and 5” residential and irrigation wells, Oxi acetylene torches    Price:  $45,000

SMEAL 5T PUMP HOIST  (Ref#2926Tb)  Manufactured 1973, telescoping mast, new cable and hydraulics, mounted on 2009 Chevy 3500 dually, 190,000 miles  Price:  $48,000

SMEAL 5T PUMP HOIST  (Ref#2974T)  Built 1971, mounted on 2005 Ford F650 truck, 138,000 miles, truck and rig in working condition  Price:  $59,500

SMEAL 5T  (Ref#1625T)  mounted on 2007 GMC 3500 automatic, approx 70,000 miles  POR

SMEAL 5T (Ref#13300RA) Manufactured 2005, mounted on Ford F550 4x4 with diesel engine, AC, maximum capacity 12000#, per line 3000#, sandreel, toolboxes, heavy duty trailer hitch, sand reel pump hoist, max capacity 12,000 / per line 3,000 / max lay back 1 line/10 feet, approx 144,000 miles  Price:  $42,500

SMEAL 5T PUMP HOIST  (Ref#8971T)  Manufactured 2004, mounted on 2004 Ford F750 truck, approx. 21,000 miles, Cummins 5.9 engine, 7 speed transmission, 33,000# GVWR, no def, air brakes, air to rear, 4 x 2 drive, cathead, remote, no sandline  Price:  $65,000

SMEAL 5T PUMP HOIST  (Ref#9918T)  Manufactured 1993, mounted on 1999 Ford F350 4 x 4 truck (245,000 miles), 6.8L V10 gas engine, automatic transmission, new tires, sandline with free fall, pipe racks, RKI service body  Price:  $67,000

SMEAL 5T  (Ref#935N)  Manufactured 2004, mounted on 2000 Sterling truck (not 4 x 4) with Cat engine, remote control, 2 rear hydraulic leveling jacks, toolboxes, pipe racks, no cathead, no sandline, excellent condition  Price:  $80,000   Tools avalable at extra cost.

SMEAL 5T PUMP HOIST  (Ref#6721T)  Unmounted, Manufactured 2003, 750’ sandline, wire reel, pipe rack, remote control, 2 rear hydraulic jacks (plumbed for front jack)  Price:  $26,500

SMEAL 5T PUMP HOIST  (Ref#909T)  Unmounted, remote cable, hydraulic pump and all tools in tool boxes.  440’ of 2” pipe, 360’ of 3” Certa lock pipe, 950’ of 1” air hose, all fittings seen in photos (trailer in photo not included)  Price:  $31,500

SMEAL 5T PUMP HOIST  (Ref#9161T)  Manufactured 1982, Unmounted, telescoping mast, remote control (needs rewiring), no cathead, no sandline, 2 pipe racks, 2 rear hyd leveling jacks  Price on Request

SMEAL 5T PUMP HOIST  (Ref#7563T)  Mounted on Ford 4WD truck with blown 6.0 ltr diesel engine, telescoping mast, remote control available but not connected, no sandline, 2 rear hydraulic leveling jacks  Price: $17,500

SMEAL 5T PUMP HOIST  (Ref#6058T)  Manufactured 1975, mounted on 1995 Ford 4WD dually truck with 7.5 liter engine, 2 drums, main drum has stem down, 2 leveling jacks, truck 280,000 miles, hoist last used Summer 2023. Rig and truck both start and run  Price:  $27,600

SMEAL 5T  (Ref#13258T)  Mounted on 2001 Ford F550 4 x 4 truck with new diesel engine, completely gone through and ready to work  Price:  $47,500

SMEAL 5T PUMP HOIST  (Ref#11390T)  Manufactured 1976, mounted on 1994 Ford F350 4 x 4 truck, 7.3 diesel engine, 5 sp transmission, newer brakes, 9’ utility body, 170,000 miles, 35,000 miles on rebuilt engine, 2 old style pipe racks, corded remote, front jack and wire winder  Price:  $42,500

SMEAL 5T PUMP HOIST  (Ref#2892T)  Manufactured 1994, mounted on 1998 GMC Sierra 4-wheel drive with gas engine, 5 speed, bed rusted, Monroe utility box rusted, remote control, telescoping mast, no cathead, no sandline, toolboxes  Price:  $29,500

SMEAL 5T PUMP HOIST  (Ref#8340Tf)  Mounted on 1996 International truck with diesel engine, remote control, 9’ utility bed, Miller welder and generator, 2 rear hydraulic leveling jacks  Price on Request

SMEAL 5T PUMP HOIST  (Ref#6418T)  Mounted on 1992 Ford 2-wheel drive truck, V10 gas engine, PTO, 5 speed transmission, no cathead, no sandline, no remote but hookup is there and he has a block for it  POR

SMEAL 5T  (Ref#1067Na)  Mounted on 1992 Ford F350 4-wheel drive, dual wheels, 8’ flatbed, 460 gas engine, no cathead, 10,000# main winch, remote control, aluminum and steel toolboxes, 2 pipe racks, brand new tires, new fenders, 35’ mast, 100,000 miles  Price:  $42,500

SMEAL 5T PUMP HOIST  (Ref#3018T)  Mounted on 1990’s Ford F350 truck 2WD with 7.3L diesel engine, PTO, windmill extension, dual back wheels, no sandline, no cathead, sitting a while, running when parked  Price:  $20,000

SMEAL 5T  (Ref#9374T)  Manufactured 1995, mounted on 1995 Ford F450 2-wheel drive truck with diesel engine, service body with toolboxes, 2 rear leveling jacks, remote control, no sandline  Price:  $29,500

SMEAL 5T PUMP HOIST  (Ref#3483T)  Manufactured late 1970’s, 36’ derrick, mounted on 1992 Ford 450 2-wheel drive with diesel engine, standard transmission, new tires, toolboxes, no remote (but plumbed for it), no sandline, no cathead, 2 rear hydraulic leveling jacks  Price:  $42,500

SMEAL 5T PUMP HOIST  (Ref#1289T)  Manufactured 1987, mounted on 1989 Ford F450 truck with 7.3 Ford diesel engine, manual transmission, 167,710 miles, winch valve needs work and valve leak inside of ram on jacks  Price:  $27,500

SMEAL BT5  (Ref#13706Tb)  Manufactured 1987, mounted on 1997 Ford 450 with diesel engine, 2 wheel drive, 2 rear hyd jacks, no remote, no cathead, no sandline  POR

SMEAL 5T PULLING UNIT  (Ref#1618T)  Manufactured 1987, double drum, 3 toolboxes on each side, mounted on 1987 Chevrolet single axle truck with 350 hp gas engine (truck has been sitting, needs work), rear leveling jacks, no cathead, no sandline  Price:  $14,500

SMEAL 5T (Ref#7607TA) Manufactured 1986, 35' mast, mounted on Ford F150 2 wheel drive with diesel engine, service body with toolboxes, remote control, sandline, bailer, 2 rear hydraulic leveling jacks  Price: $30,000

SMEAL 5T PUMP HOIST  (Ref#1258T)  Built early 1990’s, single line, 36’ derrick, remote, mounted on 1993 International 4700 truck with diesel engine, 6 speed transmission,  toolboxes, rig runs well, brake lines on truck need work (rusted out), needs batteries, has not run since 2015  Price:  $25,000

SMEAL 5T PUMP HOIST  (Ref#3248T)  Manufactured 1980’s, mounted on 1997 Chevy 3500 2-wheel drive truck with diesel engine, service body with toolboxes, telescoping mast, new tires, new batteries, new cable, no remote, good running condition  Price:  $42,500

SMEAL 5T PUMP HOIST  (Ref#5470Tb)  Built 1985, mounted on 2000 Ford F450 Super Duty truck with 7.3 diesel engine, cable remote, remanufactured transmission installed in 2016, new diesel injectors installed 2021, truck starts and runs, excellent condition  Price:  $37,500

SMEAL 5T  (ref#4620Ta)  Manufactured 1978, mounted on 2000 Ford F550 4 x 2 truck with 7.3L diesel engine, 146,000 miles, 6 speed manual transmission, cathead, hoisting line, sandline, toolboxes  Price:  $39,500
Available at extra cost:
HYDRAULIC GROUT PUMP  (Ref#4620Tb)  Armstrong 5 x 6 piston pump, designed to pump 60 gpm, all hydraulic, variable speed, 95 gpm fresh water pump 

SMEAL 5T (Ref#15536R) upgraded to pull 8500# single line pull, telescoping mast, mounted on 1986 Chevy C70 2-wheel drive truck with new Chevy 350 engine,new hydraulic pump, new spool valve, new cable, aluminum radiator, remote control, winch line, 1000' of 3/8" sandline, no cathead, 1 front & 2 rear hydraulic leveling jacks  Price:  $39,500

SMEAL 5T PUMP HOIST  (Ref#1202T)  Manufactured 1970’s, mounted on 2016 Dodge Ram 4500 (not 4 x 4) with diesel engine, no sandline, toolboxes  Price:  $57,500

SMEAL 5T  (Ref#9156R)  sandline, 25' mast, mounted on 1983 Ford F700 truck with diesel engine Price on Request

SMEAL 5T (Ref#13194R) Unmounted, sandline, no remote, no cathead, 2 rear hydraulic leveling jacks, toolboxes  Price on Request

SMEAL 5T (Ref#6974NB) Manufactured 1978, PTO, mounted on 1983 International with diesel engine, remote control, sandline, 2 rear hydraulic leveling jacks, windmill extension, needs paint and new hoses, sitting a while but running when parked  Price:  $18,500  

SMEAL 5T  (Ref#7217Ta)  Manufactured 1974, unmounted, remote control, no cathead, 2 hydraulic leveling jacks in rear, toolboxes  Price:  $14,500

SMEAL 5T (Ref#8523T) – two available

SMEAL 5T  (Ref#3430N)  Manufactured 1993, mounted on 2002 Ford F450 4 x 4 truck with diesel engine, sandline, cathead, remote  Price:  $37,500

SMEAL 5T (Ref#6636R) Manufactured 1992, PTO, mounted on 1992 Ford F350 4x4 with diesel engine, remote control, cathead, sandline spool (no line), pipe rack, 2 rear hydraulic leveling jacks  Price on request

SMEAL 5T  (Ref#2240T)  Manufactured 1977, mounted on GMC truck with 292 gas engine, PTO, mainline, sandline, pipe racks, remote control, ready to go  Price:  $29,500

SMEAL 5T  (Ref#9807Ta)  Built late 1970’s, mounted on 1992 Ford single axle truck (2 wheel drive) with gas engine, PTO, no sandline, toolboxes, hoist is good, truck runs but it should be remounted, currently working  Price:  $26,500

SMEAL 5T  (Ref#6543R)  Manufactured 1970's, mounted on 1988 Ford F350 4 x 4 Super duty XLT, 7.3 diesel engine, 56,500 miles, toolboxes, cathead, 2 rear leveling jacks, 30' mast, no sandline  Price:  $37,500

SMEAL 5T PUMP HOIST  (Ref#2690T)  Sandline, no cathead, remote control, 13’ utility body, toolboxes, mounted on 2000 Ford F550 2WD with diesel engine, PTO, 2 rear hydraulic leveling jacks  Price:  $23,500

SMEAL 5T (Ref#9044Nb) mounted on 1979 International all wheel drive with gas engine, mast with windmill extension, remote control, mainline, sandline, toolboxes, 2 rear hydraulic leveling jacks  Price:  $22,000

SMEAL 5T (Ref#13911RB) PTO, mounted on Chevy 1 ton, remote control, sandline, toolboxes  Price:  $19,000

SMEAL 5T (Ref#15439R) mounted on Ford F550 4x4  Price on request

SMEAL 5T PUMP HOIST  (Ref#7661Tc)  Unmounted, 1980’s hoist, telescoping mast, big winch, no sandline, no cathead, 2 rear hydraulic jacks  Price on Request

SMEAL 5T  (Ref#13949T)  Unmounted, sandline, 30' mast  POR

SMEAL 5T  (Ref#3403Tb)  Manufactured 1982, cathead, sandline, mounted on 1979 International Harvestor truck (truck is no good), rig has not run for 10 years  Price:  $13,500

SMEAL 5T  (Ref#7179Tb)  Mounted on Ford F450  Price:  $29,500

SMEAL 4T  (ref#14087T)  32' mast, mounted on 1999 Chevy 1-ton HD 4 x 4, 454 Chevy engine, no sandline  POR

SMEAL 4T PUMP HOIST  (Ref#7948T)  Mounted on 1995 Ford Super Duty with diesel engine, toolboxes, no remote, 2 rear hydraulic leveling jacks  Price:  $42,500 

SMEAL 4T  (Ref#1996Nb)  mounted on 1992 Chevy truck with 17' bed, 3116 Cat engine, PTO, remote control, 3 hyd leveling jacks  Price:  $19,000

SMEAL 4T BT SERIES PUMP HOIST  (Ref#445T)  1990 International 4900 Series truck with mechanics body, air brakes, 466 IHC engine  Price:  $22,500 USD

SMEAL 4T PUMP HOIST  (Ref#8425T)  Manufactured 1986, no sandline, mounted on 1986 Chevy 3500 Dually with 350 gas, 2 wheel drive, no cathead, has remote,  toolboxes, 9' bed, garage kept, 95,000 miles  Price on Request

SMEAL 4T PUMP HOIST  (Ref#9542T)  Manufactured early 1970’s, needs new truck, running condition  Price unmounted:  $14,500

HUNKE 3T  (Ref#5062Ta)  Manufactured 2017, double/triple line, no sandline, mounted on 2016 GMC 4x4 truck with 6 liter gas engine, manual transfer case, automatic transmission, no oil leaks, 2 rear hydraulic jacks, remote control, 7 toolboxes, 2 pipe racks, 17,000 miles on truck, 1230 hours on rig  Price:  $72,500

HUNKE 3T PUMP HOIST  (Ref#2605T)  Manufactured 2016, mounted on 2016 Ford XLT F350 4x4 truck with 6.2L engine, approx. 130,000 miles, automatic transmission, heavy duty snow plow front springs, 3 leaves added to rear to firm up the ride, 9’ utility body, Rino liner in bed with rubber mat, wire rack for 1000’ spool of wire, pipe rack, hydraulic wire winder, weighted safety hook, stored inside, boom stored poly spool available for an additional cost  Price:  $102,500

HUNKE 3T  (Ref#15188Tb)  2’ mast extension, long racks, cathead, power to rear, wire spool brackets, (2) pipe racks (driver’s side is powered), rope sheave, 11’ fiberglass utility body with welder compartment, well maintained, mounted on 2014 Dodge Ram  Price:  $107,500

SMEAL 3T PUMP HOIST  (Ref#2975T)  Manufactured 2004, telescoping mast, remote, control, mounted on Ford F450 4-wheel drive with bad engine, hoist is in good shape, no sandline, no cathead, toolboxes, 2 rear hydraulic leveling jacks  Price:  $37,500

SMEAL 3T PUMP HOIST  (Ref#3405Ta)  No cathead, no sandline, telescoping mast, mounted on 2005 Ford F250 4-wheel drive truck with gas engine, PTO, 2 rear hydraulic leveling jacks, no remote  Price:  $32,500

SMEAL 3T PUMP HOIST  (Ref#4491T)  Manufactured 2003, new cable and hoses, no sandline, mounted on 2020 GMC 4 x 4 truck with 9’ custom body, less than 1000 miles, pipe racks Price on Request

SMEAL 3T  (Ref#379N)  Manufactured 2003, mounted on Ford F450 4x4 truck powered by 6.0 diesel engine, 82,000 miles, 12’ Omaha body, 6’ side box, 100 gallon fuel tank, welder    Price:  $33,500

SMEAL 3T PUMP HOIST  (Ref#15519)  Manufactured 1978, mounted on 1999 Chevy 1-ton 4 x 4 truck with diesel engine, utility bed, remote control, sandline, no cathead, toolboxes, 2 rear hydraulic jacks  Price:  $32,500

SMEAL 3T  (Ref#11725T)  standard mast, no sandline, no cathead, mounted on 1999 Ford F250 2wd truck, 5.4L gas engine, PTO, (engine had a 3 valve head, now has a 2 valve head), 8’ utility bed, remote not hooked up  Price:  $37,500

SMEAL 3T PUMP HOIST  (Ref#2597T)  Manufactured 1980’s, mounted on 2000 Ford 550 2wd truck with 7.3 diesel engine, PTO, sandline, no cathead, plumbed for remote, toolboxes, 2 rear hydraulic leveling jacks, running condition  Price:  $37,500

SMEAL 3T  (Ref#3910T)  Manufactured 1997, no sandline windmill extension, mounted on 1997 Ford F350 single axle 4 x 4 truck with 7.3L Powerstroke diesel engine, no cathead, 153,000 miles  Price:  $33,500

SMEAL 3T  (Ref#7789Ta)  Manufactured 1985, sandline, no cathead, 36' mast, mounted on 1987 Ford 1-ton 4x4 truck, 6.7L diesel engine, 5 speed transmission  PRICE:  $21,500

SMEAL 3T  (Ref#7080T)  Mounted on mid 1980's Chevy truck, 454 engine, no sandline, hydraulic cathead, 2 leveling jacks, 9' utility bed  POR

SMEAL 3T PUMP HOIST  (Ref#6763T)  Manufactured 1972, mounted on 2006 Ford dually 4WD with diesel engine, 5 speed transmission, remote control, 31’ telescoping mast, 2 rear leveling jacks  Price:  $32,500

SMEAL 3T  (Ref#7520T)  Mounted on 1993 GMC dually 4 wheel drive truck with 454 gas engine, remote control, sandline, telescoping mast, toolboxes, 2 rear hydraulic leveling jacks  Price:  $21,500

SMEAL 3T PUMP HOIST  (Ref#5857T)  Mounted on 1992 Dodge 4-wheel drive truck with diesel engine, PTO, 32’ mast, toolboxes, no sandline, no cathead, no remote, 2 rear hydraulic leveling jacks, good tires  Price:  $32,500

SMEAL 3T  (Ref#6292R)  Mounted on 1990 Chevy 2500 truck, 350 gas engine, 65,000 miles, single line, has pullies for 3 lines, hydraulic pulldown  Price:  $24,000

SMEAL 3T  (Ref#2351T)  Unmounted, sandline (nop line), no cathead, remote (not wireless)  Price:  $10,500

SMEAL 3T  (Ref#3884Tb)  sandline, 40' mast, no cathead, mounted on 1988 Ford 350 with 7.3L diesel (truck engine does not run, needs to be overhauled)  Price:  $11,500

SMEAL 3T  (Ref#9905T)  Mounted on 1989 Ford F350 Superduty 4-wheel drive, only 70,000 miles, no sandline (but sandline wheel available), front winch Price:  $27,500

SMEAL 3T PUMP HOIST  (Ref#3973Ta)  Mounted on Dodge truck   POR

SMEAL  (Ref#11625T)  460 gas engine, no sandline, no cathead, 24' mast, mounted on 1996 Ford F350 1-ton 4 x 4 truck  Price:  $14,500

SMEAL R2RG PUMP HOIST  (Ref#8872Tb)  No sandline, no cathead, mounted on older Ford with gas engine, PTO, remote control, utility bed, 2 rear hydraulic leveling jacks  Price:  $18,000

SMEAL 32B  (Ref#8349R)  Mounted on 1994 Chevy 3500 steel bed truck, 87,000 miles, high idle, main line, sandline, new cables, hydraulic outriggers  Price:  $30,000

SMEAL 32B PUMP HOIST  (Ref#1559T)  Sandline, mounted on two wheel drive 1992 Kodiak with Cat 3116 engine, PTO, low miles and hours on truck, new tires, utility bed, toolboxes, no remote, 2 front and 2 rear hydraulic leveling jacks, running condition  Price:  $27,500

SMEAL 32BT  (Ref#7894Ta)  Manufactured 1994, no sandline, no cathead, 32' mast, mounted on 1994 Ford F350 4 x 4 truck, utiity boxes, 47,000 truck miles, located Canada, components were assembled in Canada   PRICE:  $18,500 USD

PULSTAR P38 PUMP HOIST  (Ref#3196T)  Manufactured 2008, sandline, hydraulic breakout ram, mounted on 2008 Peterbilt 335, 198,000 miles, PacCar engine, Eaton 10 speed transmission, spring suspension, single rear axle with tag, front and rear leveling jacks, cutting torch, bulk drip oil tank and bottles, well maintained  Price:  $215,000

PULSTAR P38000HD PUMP HOIST  (Ref#10424T)  Manufactured 2007, sandline, ¾” X 210’ winch line, Oil Gear PVG-100 hydraulic pump, mounted on 2006 Peterbilt 357 truck with Cat C11 diesel engine, cross locks 13 speed gear, reduction transmission, heavy duty suspension, 44,033 miles, 15,486 hours (as of January 2024), fully operational  Price:  $235,000

PULSTAR P38000 PUMP HOIST  (Ref#9499T)  Manufactured 2005, main line, tail out line, no sandline drum, mounted on Sterling truck with 55,000 miles, 85% tires  Price:  $187,500

PULSTAR P12000 PUMP HOIST  (Ref#2405T)  Manufactured 2014, mounted on 2014 Dodge 5500 4-wheel drive truck with diesel engine, PTO, remote control, sandline, wire winder, oil cooler, 3 hydraulic leveling jacks, fully loaded  Price:  $97,500

PULSTAR P12 PUMP HOIST  (Ref#8333T)  Manufactured 2014, mounted on 2014 Dodge 5500 4 x 4 truck with 6.7L diesel engine, PTO, tailout winch, sandline, main winch, 46’ mast, front outrigger, 2 back outriggers, toolboxes, 162,000 approx miles, approx. 5500 hours (both idle and run time), new turbo diesel has approx. 300 hours, new DEF approx. 100 hours, resealed transmission  Price:  $122,500

PULSTAR P10HD  (Ref#5975T)  Built 2015, mounted on 4 x 4 Dodge 5500 with diesel engine, 46' mast, low hours, 31,000 miles, extras, very clean  Price on Request

PULSTAR P10  (Ref#7937T)  Mounted on 2001 Ford F450 2WD with diesel engine, remote control, sandline, no cathead, toolboxes, 1 front and 1 rear hydraulic leveling jacks  Price on Request

PULSTAR P10000  (Ref#7213T)  Windmill extension, mounted on 2005 International truck with rebuilt DT466 engine, 7 speed Spicer transmission, remote control, sandline, toolboxes, 3 rear hydraulic leveling jacks  Price:  $57,500

PULSTAR P7000  (Ref#2029T)  Mounted on 2006 Ford 4-wheel drive truck with new diesel engine and transmission, remote control, no sandline, no cathead, utility bed with toolboxes, 3 hyd leveling jacks Price on Request

PULSTAR P7000  (Ref#5959T)  Manufactured 2004, 165 cfm air compressor, 400’ air electric hose reel, mounted on 2004 International 4300 truck, 363,000 miles, DT466 Allison transmission, remote control, sandline, no cathead  Price:  $62,500

PULSTAR P7000  (Ref#3657T)  Built 2000, mounted on 2000 Ford F450 4 x 4 truck, 7.3L diesel engine, 235,000 miles  Price:  $47,500

PULSTAR P7 PUMP HOIST  (Ref#9354T)  Mounted on 1999 Ford F450 truck 4 wheel drive, 7.3 Power Stroke diesel engine, standard transmission, new clutch 2019, Pac brake exhaust brake, new front drive tires 2019, rear tires 2018, approx 115,000 miles, corded remote  Price:  $80,000

PULSTAR (Ref#14048T)  2008 Dodge 5700  Price:  $64,500

PULSTAR P4000  (Ref#6351T)  Manufactured 2005, 32' mast, no sandline, mounted n 2005 Ford F350 1-ton truck  Price:  $65,000

SEMCO S25000  (Ref#12339Ta)  Manufactured 2009, mounted on 2009 F750 truck with 6.7 Cummins diesel engine, engine and transmission rebuilt 2017, 2 rear leveling jacks, no sandline  Price:  $89,500 

SEMCO S25000  (Ref#12339Tb)  Manufactured 2005, mounted on 1995 International tandem axle truck with Detroit Series 60 engine, 9 speed transmission, rear jacks only, no sandline Price:  $89,500 

SEMCO S15000  (Ref#3836T)  Buit 2019, mounted on 2020 Freightliner 108SD truck, tooling  Price:  $260,000

SEMCO S15000  (Ref#11659Tb)  Manufactured 2010, no sandline drum, 200’ of ¾” mainline, mounted on 2006 International 4300 truck with DT466 diesel engine, 4 hyd jacks  Price:  $89,500  

SEMCO S15000  (Ref#12339Tc)  Manufactured 2009, sandline drum (no line on it), new drum motor and brake,  mounted on 2003 Sterling tandem axle truck with Detroit Series 60, sandline, 4 leveling jacks Price:  $89,500 

SEMCO S15000  (Ref#12142R)  Manufactured early 2000's, 1000' of 9/16 sandline, 5/8" mainline, 54' mast, power tongs, mounted on 1997 FL70 Freightliner truck with diesel engine    PRICE:  $79,500

SEMCO S15000 PUMP HOIST  (Ref#2573T)  Manufactured 2000, mounted on Ford F650 truck with Cat head, approx. 182,000 miles  Price:  $77,500

SEMCO 15000 WORKOVER RIG (Ref#7711N) Manufactured 2000, PTO, mounted on 1996 Ford F800 (not 4x4) with Cummins engine, power tongs, 1.9" to 2-7/8" air slips, 2-3/8" to 2-7/8" power tongs, water well slips for PVC, pipe wrenches, hand tools, tubing subs 1.9" to 2-3/8", 2" and 4" Balon valves and fittings, used for coal bed methane wells, can pull 2700' of 2-=7/8" tubing single line, excellent condition, fully equipped and ready to work  Price:  $145,000

SEMCO S12000H PUMP HOIST  (Ref#3338T)  Manufactured 2021, mounted on 2012 International cab with 500 miles on replaced 220 HP Max Force engine, hot shift PTO, DEF system removed from truck, automatic transmission, 2 speed winch with grooved drum, 2000’ capacity sand reel, 44’ hydraulically telescoping mast, 140’ fpm line speed, lifting capacity 36,000 lbs  Price:  $115,000

SEMCO S10000  (Ref#7088T)  Double drum with only one line, no welder, mounted on 1990 GMC truck with Cat engine, jacks, lifter, clamps and some tools  Price:  $53,500

SEMCO S8000  (Ref#8841T)  Manufactured 2012, mounted on 2006 Peterbilt 335 truck, Cummins engine, automatic transmission, 24,000# pullback  Price:  $70,000

SEMCO 8000 (Ref#14214R) Manufactured 1988, PTO, mounted on ‘79 GMC 7500, sandline, with hydrofrac unit 2500psi 45gpm pump, 1"-3" elevators, hand tools, includes '94 Ford LT8000 water truck, 1500 gallon tank, 210 Cummins engine, 6 speed trans, pipe rack, toolbox, 750lb crane  Package Price:  $67,500

SEMCO 8000 (Ref#7900R) mounted on GMC 2 wheel drive with gas engine, remote control, mainline winch, hydraulic breakout wrench, no cathead or sandline, pipe racks, 2 rear outriggers  Price on request

SEMCO S6000 PUMP HOIST  (Ref#1667T) Manufactured 2003, no sandline, mounted on 2003 Ford F550 4 x 4 truck with 6.0L diesel engine, wire remote control with throttle, cracked injector in 6.0L diesel engine (needs repair)  Price as is:  $29,500

SEMCO S6000 PUMP HOIST  (Ref#2953T)  Manufactured 1993, sandline, 30’ mast, mounted on 2004 Ford F550 4 x 4 truck with 6.0 ltr engine, no remote   Price:  $32,500

SEMCO S6000 PUMP HOIST  (Ref#3970T)  2 speed winch, sandreel, developmental air, mounted on 2004 4 x 4 Ford F550 truck with diesel engine  Price on Request

SEMCO 6000 PUMP HOIST  (Ref#8803T)  Mounted on 1995 Ford dually 1-ton truck with new gas engine, utility bed, 2WD, no cathead, no sandline, 2 rear hydraulic leveling jacks  Price:  $52,500

SEMCO S6000  (Ref#11618T)  Manufactured 1988, mounted on 1988 Ford 350 4 x 4 truck, 7.3L diesel engine, 90,000 miles, 1 winch, no cathead, no sandline, 2 rear jacks, stored inside  Price on Request

SEMCO S6000 PUMP HOIST  (Ref#2926Ta)  Manufactured 1986, mounted on 1986 Ford F350 truck, 89,000 miles, new transmission and rear end, telescoping mast  Price:  $35,000

SEMCO S6000 PUMP HOIST WITH KYLE HYDROFRACKER  (Ref#6981Ta)  Mounted on 1988 International S1600, 5-1/2” packer, 840’ 1-1/2” frack pipe, 80’ zone frack pipe  Price:  $137,500

SEMCO 4000 PUMP HOIST  (Ref#3953T)  Manufactured 2010, 3 lines, 800’ baiing line, telescoping mast, mounted on 2014 Dodge Ram 5500 4WD with diesel engine, approx. 24k miles  Price:  $89,500

SEMCO S4000  (Ref#13331T)  Manufactured 2005, 8000# cap, no cathead, no sandreel, utility bed, 33' mast, remote control, toolboxes, mounted on 2016 Dodge Ram 3500 4 x 2 truck with Cummins diesel engine, 2 rear hydraulic jacks, front fender is damaged  Price:  $52,500

SEMCO 4000 (Ref#4067N) Manufactured 2003, low hours, PTO, mounted on 1994 GMC with diesel engine (not 4x4), (truck not good), bailing drum, pipe rack, 2 rear hydraulic leveling jacks  Price:  $21,000

SEMCO S4000 (Ref#13300RB) Manufactured 2000, mounted on Ford F450 4x4 with diesel engine, 44' derrick, hydraulic wire reel with free fall, remote control, 8x12 steel flatbed, toolboxes, heavy duty trailer hitch, approx 225,000 miles, sitting since 2019, truck does not start Price:  $35,000

MONITOR M42 PUMP HOIST  (Ref#9137T)  Built 1973, mounted on 2009 Ford F350 truck with V10 gas engine, approx. 197,000 miles, no sandline, ready to work  Price:  $45,000

MONITOR M35  (Ref#10394Na)  30,000# capacity, sandline, aux line, mounted on International 1600 4-wheel drive truck with gas engine, PTO, Smeal fail-safe brakes on both drums, 130' of new 5/8" line, no tools  PRICE:  $33,500

MONITOR M35  (Ref#13253Ra)  Manufactured 1991, mounted on 1991 International 4 wheel drive truck with DT466 Detroit diesel engine, no tooling, 2 jacks  Price:  $33,500

MONITOR 35 (Ref#13714RB) needs new lines, oil needs to be replaced, PTO, sandline, mounted on Dodge 1 ½ ton, sitting 7 years  Price $16,500

MONITOR 34  (Ref#10043Ra)  mounted on 1987 Dodge 1-ton 4 x 4 truck, 360 gas engine in truck, 42' mast, fiberglass service body, plastic pipe reel, 8000# single line, 400' of 3/8" line, 2 rear jacks  Price:  $10,500

MONITOR M34  (Ref#10093R)  Reworked 2005, 42' mast, PTO, mounted on 1994 GMC 6500 truckwith Cat diesel engine, Allison transmission, 2hyd jacks, toolboxes, 1 winches  Price:  $29,500

MONITOR 34  (Ref#4475Tb)  Isuzu 4LE1 engine, mounted on 1995 F350 4 x 4 truck  Price: $21,500

MONITOR M33 PUMP HOIST  (Ref#9739R)  mounted on 1992 Ford F350 4 x 2 truck, single line, been sitting idle for 3 years  Price:  $27,500

MONITOR M33 PUMP HOIST  (Ref#9321Tb)  Mounted on 1999 Ford F350 2-wheel drive truck, V10 gas engine, auto transmission  Price:  $26,500

MONITOR M33  (Ref#13491T)  6T hoist completely rebuilt, new hydraulic hoses, pins and bushings.  Mounted on 1997 Ford F450 2wd truck 7.3 diesel engine, 11' service body, 123k miles  Price:  $26,500

MONITOR M33  (Ref#7489Ta)  40' mast, service body, GMC truck, automatic, used  Price:  $42,000

MONITOR 33  (Ref#2520Ta)  Manufactured 1980's, mounted on 1990 GMC Topkick with gas engine, 2 wheel drive, no remote, no sandline or cathead, 2 rear hyd leveling jacks  Price  $27,500

MONITOR M-33 (Ref#11730R) unmounted, manufactured 1972, hydraulic pump, no cathead, no sandline, no remote control  Price:  $10,500

MONITOR M34  (Ref#10394Nb)  8,000# single line capacity, mast with 2' extension (37' total height), 130' of new 5/8" line, mounted on International 1600 4-wheel drive with gas engine, no tools  Price:  $37,500

MONITOR M33 (Ref#3693N) Telescopic 33' mast with remote, mounted on 2000 Ford F250, located Canada    PRICE:  $30,000 CDN

MONITOR M33  (Ref#1996Na)  Manufactured 1977, unmounted, telescoping derrick, remote available, no sandline, 2 rear hyd leveling jacks, no tools  Price on Request

MONITOR 33  (Ref#15678)  33' telescoping derrick, remote control, custom designed two rear hydraulic stabilizing jacks, 8' steel deck, hydraulic driven pump pulling drum, two upright cabinets, two under deck boxes and two under deck fuel tanks, mounted on 2002 F550 Ford truck with 7.3 power stroke with 6-speed manual transmission  Price:  $75,000

MONITOR 33  (ref#2057N)  mounted on 1988 Ford 2-ton truck with rebuit Jasper 370 hp gas engine, air brakes, 5 & 2 transmission, PTO, 1 winch, 2 rear hyd leveling jacks  Price:  $17,500

MONITOR M33  (Ref#5410Rb)  not mounted, sitting a couple of years  Price:  $8,500

MONITOR PUMP HOIST  (Ref#9133Tb)  Unmounted, no line, no engine, not used since 2015  Price on Request

MONITOR PUMP HOIST  (Ref#8340Tg)  Mounted on Freightliner with diesel engine, utility body, 2 rear hydraulic leveling jacks  Price on Request

MONITOR PULLING UNIT  (Ref#2281N)  mounted on 1988 Chevy 4 wheel drive truck with 350 Chevy engine, 6,000-8,000# hoist  Price:  $22,500

MONITOR 32B PUMP HOIST  (Ref#8321T)  3 speed transmission on winch, mounted on 2000 Chevrolet truck with 454 engine, manual transmission, 11' utility body, 35' mast, extended boom with 3rd leg provision, ready to work, single line machine, will accommodate 2 line block, pipe rack  Price on Request

MONITOR PUMP HOIST  (Ref#4329T)  Unmounted, single line, can pull 25’ without extending the mast, telescoping mast, remote control, no cathead, no sandline, 2 rear hydraulic jacks  Price on Request

MONITOR PUMP HOIST  (Ref#4836Ta)  unmounted  Price on Request

JESSEN M-33 PUMP HOIST (Ref#2591R) Manufactured 1979, PTO, mounted on Ford F-600 2 wheel drive with propane engine, 1 winch, 30’+ mast, no sandline or cathead, 2 rear leveling jacks, utility boxes, ready to go.  Second rig available:  same specs as above, manufactured 1977, sitting a long time, needs work Price:  $19,500 for both

JESSEN PUMP HOIST  (Ref#1477T)  Single line, mounted on 1-ton Ford truck with diesel engine, utility body, 2 rear hydraulic leveling jacks  Price:  $16,500

PUMP HOIST  (Ref#2162T)  Approx 6000# capacity, mounted on 1990 Chevy 3500, gas, 2 WD, 1996 Bloom winch  Price:  $19,500

FLEETMASTER 2 TON PUMP HOIST  (Ref#158N)   1974, mounted on 1989 International truck, diesel DT360 International engine, spudder attachment, 32' derrick, excellent condition    PRICE:  $29,500

CYCLONE PUMP HOIST/SWAB RIG  (Ref#10544N)  Manufactured 1978, Capacity of 4,000#, split single drum, mounted on Ford F350 single axle dual wheel rear with 4 speed transmission, gasoline engine, tool boxes, 2 hydraulic leveling jacks, 5 speed transmission on hydraulic drawworks, 30 gallon hydraulic tank, twin disc air clutch, 2 piece square tubular boom retractable to length of truck expands hydraulically to 30', 400' of 1/4" cable, boom will tilt back to 12' behind truck to swab a well or pull a pump    PRICE:  $17,500

CYCLONE 30 PUMP HOIST  (Ref#5688T)  mounted on 1987 Chevy 1 ton truck, 350 cu in 4 bolt main, currently working  Price:  $14,000

CYCLONE PUMP HOIST  (Ref#13788)  Manufactured 1981, 125 SDS Grimmerschmidt compressor, single drum, 1 front 2 rear hydraulic leveling jacks, 12,000# capacity, pipe rack, 75' of 5/8" cable, toolboxes  Price on Request

CYCLONE PUMP HOIST  (Ref#466N)  mounted on 1993 Ford F450 truck, fiberglass utility boxes,   PRICE ON REQUEST

CYCLONE PUMP HOIST  (Ref#8908T)  single line, now on a wheeled carrier, PTO, has a transmission, will sell unmounted  Price on Request

CYCLONE F100 PUMP HOIST  (Ref#15368T)  Manufactured 1992, rated for approx 5,000 – 6,000 lbs, mounted on 2006 Chevrolet Kodiak 5500 4 x 2 flat bed Price:  $39,500

CYCLONE F100 PULLING UNIT  (Ref#10013)  Manufactured 1990, mounted on Ford F350 single axle rear truck powered by 460 gaoline engine, 5 speed manual transmission, utility body, 10,000# capacity, aux sandline, remote control, hyd jacks in rear  Price:  $28,500

CYCLONE F40 PUMP HOIST  (Ref#8537T)  mounted on 1973 Chevy ¾ ton 4 x 4 truck, 350 Chevy engine, no sandline, no cathead, 30' mast, approx 52,500 miles  Price:  $17,500

CYCLONE F40 PUMP HOIST  (Ref#3139T)  no sandline, cathead, mounted on 1986 GMC truck with gas engne, running condition  PRICE ON REQUEST

CYCLONE F30 PUMP HOIST  (Ref#4785N)  early 1970's, mounted on 1987 Ford F800 2wd truck, Ford diesel engine, single line machine, no sandline, truck bed equipped with toolboxes, pipe rack, no tools    Price:  $17,000

CYCLONE 10 PUMP HOIST  (Ref#491N)  mounted on 1984 Railroad truck, power brakes, new battery, 500' of new pipe, 32'+ derrick, 10" bit, stems, sockts.
1975 Chevy flatbed truck with Chevy gas engine, 14' ved, 250 gallon tank, steel racks   Package Price:  $20,000

CYCLONE 5 PUMP HOIST  (Ref#5242Tc)  Mounted on 1979 Chevy truck with gas engine, 2 rear jacks, starts and runs, gone through 2022  Price:  $32,500

CYCLONE PUMP HOIST  (Ref#8340Th)  Mounted on International truck with diesel engine  Price on Request

WALKER NEER 32 SPECIAL  (Ref#1923N)  Manufactured 1953, 2500' drill line, 3000' sandline, 140 Waukeshaw engine, mounted on double axle trailer, 2 lines (drill line, sand line), double pole, friction clutches, fully tooled    PRICE:  $45,000

PRINCE MANUFACTURED PUMP HOIST  (Ref#1025T)  mounted on 1996 GMC 3500  2 wheel drive truck, diesel engine, 2500 psi – 3 bore, 15' mast, 2 leveling jacks, no remote  PRICE:  $12,500

HOPPER BAILER RIG (Ref#4042Ne) sitting long time but running when parked, includes 15 bailers and bucket  Price:  $18,500