March 26, 2025

DREDGES FOR SALE

For additional information please contact Anthony Iorio at Tel (516) 536 7375 - rigs@sunmachinery.com

 

CLAMSHELL DREDGE  (Ref#4205) 

105’ x 50’ x 8’, 1965 Bucyrus Erie 88B crane with 12 Cubic Yard clamshell, (2) 30” x 65’ square spuds, (2) H50 Pullmaster winches, 40 KW John Deere generator, set up with weighted spud tension system, set up to dredge 40’+, last worked 2024 Price:  $2,950,000


8” X 8” DSC MORAY DREDGE  (Ref#4185c

42.8’L x 18.5’W, 17.5’ depth, 42,000 lb overall weight, 19.5” impeller dredge pump, 25 hp cutter power, cylinder ladder lift/swing, 8” square spud, articulating rear spud, Cat 275 hp diesel engine, inline direct marine style transmission for dredge pump reduction, PLC operating system, standard equipment, power up/down winches for proper cable storage, stern kicker spud or extending leg for controlled positioning, located Florida  Price:  $300,000


MUDCAT SP915 8” AUGER DREDGE (Ref#4191)

15’ depth. 32’ length. Detroit 6 cylinder. 8” discharge. Cutter head width: 98". Capacity: 2000 gallons per minute. Thomas pump. Replaced main gear box – rebuilt box $30k, Located Pennsylvania  Price:  $80,000


MUDCAT 915 DREDGE  (Ref#4233) 

Detroit diesel engine, 3826 hours, secondary hour meter reading 985, boom, mud shield, enclosed cab, winch, 108” wide, auger, toolboxes (no trailer)  Price on Request


SRS CRISAFULLI SD110 AUGER DREDGE  (Ref#4056

Manufactured 2012, 1400 hours, Perkins 110 hp engine, 1200’ of 6” solid dredge pipe, 300’ floating pipe, used in fresh water only, currently on land in Ohio  (new cost $360,000)  Price:  $265,000


SRS CRISAFULLI SD110 AUGER DREDGE  (Ref#4131

Manufactured 2010, Perkins 110 hp engine (dredge has 640 hours), Yamaha 116 hp engine (approx. 270 hours), sitting since 2017, excellent shape
2012 Kearney trailer for piping with approx. 500’
2004 Hillsboro trailer for dredge
Located Iowa
Price:  $150,000


MUD CAT 115D DREDGE  (Ref#3731) 

Built 2020, used very little (less than one week), 15’ working depth, 8’ cut width, 17” cut height, 22.5” avg draft, Catamaran hull type, John Deere 125 hp engine, 60 gal fuel capacity, MudCat slurry pump with 8” discharge, 3000 gpm max performance, 3.5” solids passage (closed impeller),  4.3” solids passage (open impeller)  Price:  $240,000


6” CUSTOM HYDRAUILC SUCTION DREDGE  (Ref#4203) 

Gulf Atlantic 6” dredge pump mounted on a custom galvanized dredge arm, 10’ digging depth, can be upgraded to an 8” pump, John Deere hydraulic power unit powers the hydraulic pump.  TB290 excavator mounted on barge chassis through the deck, hull 34’ x 12’+, good condition, highly maneuverable and transportable, lift pad eyes, The barge features a robust frame construction suitable for operation in shallow water, maneuverability is achieved with precision using the dredge arm and winch powered spuds, includes 400’ dredge pipe, floating gear and galvanized 25 yard dewatering bin, good condition, located in Florida  Price:  $250,000


8” MUD CAT AUGER DREDGE  (Ref#3917)  Manufactured 2005, 2500 hours, 20’ depth, 24”  x 96” auger, 8” submersible pump, can produce 228 gpm @ 140’ head, Cat 275 hp diesel engine, New York  Price:  $75,000


8” CUSTOM BUILT DREDGE  (Ref#4140) 

8” discharge, 7’ cutter on 21’ elevator (part that moves while cutting), will produce one yard a minute in sandy/silty (not heavy rock) material and will push out at zero elevation 2100’, 2023 Twin 90 hp Yamaha engine, 8’ custom built self-propelled, enclosed cab, with 30’ gooseneck trailer, located Georgia Price:  $125,000


10” SWINGING LADDER BARRACUDA CUTTERHEAD SUCTION DREDGE  (Ref#4152)

  25’ ladder length, 66’l x 17’10”w (with side tanks), 4’ depth, 10’ height (spuds removed), 30” mean draft (with fuel), 10” spud length, digging depth 2’ – 19’, maximum swing (swinging ladder mode) 19’ – 26’, maximum swing conventional mode 76’ x 87’.  Cat 3406 KITA engine, Murphy EL-150-K1 day tank sender, R.R. 1000DF cutter gear 71,900 in/lb torque, Cutter’s Edge 5 blade left hand 31’ ½ ID, Fairfield reduction gear 8:1 ratio, Pullmaster winches, 12 x 10 dredge pump,  well maintained, currently on landing repairing where needed and painting, located East Coast US  Price:  $425,000
Available at extra cost:
8500’ of 10” and 12” dredge pipe in excellent condition on trailers, McElroy Fuser and 10” booster


12” x 10” ELLICOTT 370 DREDGE  (Ref#4128T) 

Built 1984, 36’L x 12’W x 4’ depth, Dredge pump engine Cat 3406, 31.5” cutter diameter w/5 blades, 40 HP, 0-39 rpm, 3840 lb cutting force, 195 lbs/in, (2) swing wiches 8000 lb, 22’ ladder, 16’ digging depth at 45 degrees, 20’ digging depth at 60 degree, 57.5’ overall length, 2000’ of flanged 10” HDPE dredge pipe and (40) 10” pipe floats, located Washington State  Price:  $150,000


12" x 10" ELLICOTT 370 DREDGE PACKAGE  (Ref#4086

Includes Ellicott 370 dredge Cat 3406 engine (Motor has been refurbished with low hours), 10 x 12 booster pump (pump has new sleeve and impeller is in great shape), 1800’ dredge pipe, pushboat with Twin Detroit engines, 6’ x 15’ barge with 14’x8” spuds, 700 gal fuel tank, McElroy fusion machine for fusing pipe w/ shoes for 8”-12” and 18”-20” pipe.  Extra new Maddox 8” x 8” pump and gearbox, many other extras and spares.  Well maintained and in excellent condition.    Located Nebraska    Package Price:  $225,000


10” x 8” MUD CAT MC2000 AUGER DREDGE (Ref#3618)

Built 2004. 10" suction, 8" discharge, 6" particle clearance. Engine: John Deere 6081 H 300 HP. Length overall: 47, width overall 8'6", height overall: 8'6". Dry weight: 28,300lb. Draft 2.5' fully loaded. Main pump: Ellicott 24" impeller, capacity: 2500 gpm @ 162' TDH. Sludge pump: Ellicott 25" impeller, 10" suction, 8" discharge, 8" particle clearance. Propulsion: Triple wrap friction drive winch. 2300lbs line pull, 50 fpm max speed. Used in the same freshwater pond since it was new, never in saltwater. 2690’ of 8” HDPE SDR 17 dredge pipe, 1 rubber discharge hose, float for discharge hose.  Located Northeast US.   Price dredge only:  $170,000 Package Price: $205,000


MUDCAT MC2000 AUGER DREDGE  (Ref#3608

4 available from 1999 – 2005, 272 hp Cat engines, the 2001 unit has a Tier 3 Cummins engine with 2500 hours, 24” diameter auger, 20,000 lb torque, 20’ depth, forward/reverse digging, currently on land, located New York  Price:  $65,000 each


IMS VERSI-DREDGE MODEL 4010  (Ref#4236

Built 1993, 4311 hours, 5.9L Cummins 177 hp 6 cylinder engine, 20’ digging depth, 8’ auger head, cable travel with windlass drive, haul trailer with pintle hitch, fittings, hose, anchor plates/stakes, floats and grip pullers.  Approximately 2000’ of `10” DHPE pipe with Gheen fittings available.  Not used since 2022, currently on land on a trailer, pipe will go on another trailer.  It’s in good condition, located in Iowa.  Price:  $175,000


10” X 12” DSC BARRACUDA SWINGING LADDER DREDGE  (Ref#4113a) 

Built 2005, 2022 Cat C15 engine, 3’-17’ digging depth, 55’ overall length (with ladder), 17’10” overall width (operational mode), 4’ hull depth, 12’ heigh (less spuds), 38” mean draft (with fuel), 11’11” width (trucking mode), (2) spuds 28’ (1145 lbs) and 30’ (1225 lbs), 70,000 lb total dredge dry weight (approx.).
3’-17’ digging depth,
Swinging ladder - Maximum cut at minimum depth 26’,  Maximum cut at maximum depth 19’
Conventional – Maximum cut at minimum depth 80’, Maximum cut at maximum depth 70’
Cat C15 engine, 2828 lb cutting force, 68,000 in/lb operating torque, 88 lb/in cutting force, 28” cutter diameter, 3” shaft diameter, 35 hp cutter rating, 0-32 rpm cutter speed.
Winches: 9617 lb pull (1st layer), 40 ft/min line speed, ½” wire, 208’ drum capacity
Hoist cylinder: 25,535 lb extending force, 41,233 lb retracting force
12” x 10” dredge pump with 32” impeller
Hoist winches: 2204 lb line pull, 81/ft/min, 3/8” wire, 83’ drum capacity
24 VDC battery, 321-645 Delco alternator
800 gal fuel capacity, 150 gal hydraulic oil capacity, operator’s charge, lighted ring buoy, handrails and kick rails, guards, early warning alarm system and engine shut down system, cabin lights, electric bilge pump, replaceable edge cutter, dredge pump priming system, dredge washdown system, high capacity service pump, hydraulic pump/engine clutch disconnect, pump/engine reduction gear, stern pulling eyes,
last used October 2023  Price:  $525,000


14" x 12" AAMCO CUTTERHEAD DREDGE (Ref#2787a)

Reworked 2013 / Repowered 1995, Hull rebuilt / refurbished 2014, 65' x 24' x 5', draft 3', 7000 gal fuel capacity. 700 HP CAT 3412 Pump engine, GIW dredge pump, 14" Suction, 12" Discharge. 300 HP Cat 3306  Aux engine, 150 HP Cutterhead drive, 40' Ladder. (2) 16" x 50' stern spuds raised and lowered via winch. (2) 16" x 50' mooring spuds, self-raising and lowering. Hydraulic pumps, motors, cylinders, controls, valves, piping, hoses, and fendering. Firefighting equipment. On blocks, stored on land, excellent condition. Located Northeast USA, in the water. Price: $475,000


16” x 16” MADDOX BOOSTER PUMP  (Ref#4050) 

Detroit 12V92TI diesel engine, mounted on skid, complete, no fuel tank, located Florida  Price:  $65,000


16" x 18" CUTTERHEAD DREDGE (Ref#3449) 

Built 2012.  102' x 23'6", hull depth 5'. Ladder length: 55'. Minimum depth: 6', max depth 44'. Center section: 36' x 11' x 5'. Side pontoons: 90' x 6' x 5'. Dredge pump: Pearce, 18" x 16". Impeller 40" diameter. Main engine: CAT C-32 Acert 1125 HP (4.369 HOURS) with TwinDisc marine transmission. Fuel capacity: 2000 gallons (shared). Aux engine: CAT C-13 ACERT 440HP with Funk hydraulic drive. Cutterhead type: 43" ID, speed 0-20rpm, 150 HP. Winches: (2) Swing: Pullmaster H-18, Ladder hoist: Pullmaster M-25, (2) spuds: Pullmaster H-18.  Spuds: 16" x 75' x 7/8" wall thickness. Standard operator cab, 6'8' with A/C and heat.  Modified gantry for longer spuds, stainless steel cutter shaft/sleeve. 2-ton jib crane for pump service. Located Northeast US. Price: $1,775,000


ELLICOTT SERIES 2070 DRAGON 20” X 20” HYDRAULIC CUTTER SUCTION DREDGE  (Ref#4062) 

20” suction pipe, 20” discharge pipe, 50’ depth, 110’10” L (with ladder raised), 72” hull length x 26’6”W x 7’6” hull depth, 3 pontoons, 4.5’ hull draft (not including spuds), 9000 gal fuel capacity, 335,521 lb dry weight, main engine Cat C32 marine 1300 hp Tier 3 with heat exchanger, Aux engine Cat C15 440 hp tier 3 with heat exchanger, 1740 hp (not including genset), 250 hp at cutter shaft, 54” diameter cutter with 14,900 lb cutting force 18-27-36 rpm.  24” x 66’2” spuds  Price:  $2,500,000


20” INLAND CUTTERHEAD DREDGE (Ref#3914) 

55’ dig depth, 70’ Ladder length, 155’ Length x 34’ breadth x 6.75’ depth, 5’ operating draft, main engine EMD 16-645 (2000 hp), 200 HP hydraulic cutter, HPU Cat 3408, (2) 500 kw Cummins KTA 19 Onan AC generator sets, Pullmaster 50 swing winches, Pullmaster 50 ladder winch, Braden 50 ton spud winch, 24” x 50’ spuds, 48,000 gal fuel capacity, fire detection system, to be sold out of USA  Price on Request


24” CUTTERHEAD SUCTION DREDGE  (Ref#3908

Built 2005, reconditioned 2009 and again in 2015, modular design of all welded steel, 133’ x 32’ x 7’ depth, 3.5’ draft (hull only), 170’ overall length, 24 x 24 HHD 62 Georgia Iron Works pump, DC motor G.E. 500 rpm, 3500 HP continuous 700 VDC armature, 9600 DC Digital drive system rated 3500 hp, 600 VAC input, 60 HZ, 72’ ladder plus 20’ extension, 700 hp electric over hydraulic cutterhead, 300 hp jet pump, 36” x 50’ (plus 40’ extensions) spuds hoisted by independent winch with 200 hp AC vector motors, (2) winches with 200 hp AC vector motors with 150,000# pull at 80 fpm.  Ladder hoist independent winch powered with 100 hp AC motor.  Dredge takes 4160 volt AC power through 3000’ of 8000 volt rated cable spooled on a diesel driven barge mounted reel.  Cat 3406 emergency generator set to operate the winches in case of power failure.  Price:  $3,500,000


GIW 10” x 12” BOOSTER PUMPS (Ref#3627b) 2,000 hours. Located Rocky Mountains Price: $200,000

12” DREDGE PIPE  (Ref#3941) 
6800’ of 12” HDPE SDR17 dredge pipe, cut ends, 40’ lengths, some connectors  $14 per foot
2800’ new 12” HDPE SDR17 dredge pipe, factory cut ends, 40’ lengths  $22 per foot
3000’ 8” HDPE SDR 17 dredge pipe with connections, like new, loaded on truck $13 per foot

12” SDR 17 DREDGE PIPE  (Ref#4113b)  approx. 10,000’  Price:  $13 per foot

12” SDR11 DREDGE PIPE  (Ref#4113c)  approx. 5000’  Price:  $13 per foot


8” SDR17 HDPE DREDGE PIPE  (Ref#4179a) 3,900’ available, 40-50’ sections, located Florida Price:  $8 per foot
10” SDR17 HDPE DREDGE PIPE  (Ref#4179b)  750’ available,  40-50’ sections, located Florida  Price:  $12 per foot
12” SDR17 HDPE DREDGE PIPE  (Ref#4179c) 24,300  ’ available, 40’-50’ sections, located Florida  Price:   $15 per foot


See more dredges for sale on our website: dredges for sale. Let us know if you have any dredges or dredge equipment for sale.

For additional information please contact Anthony Iorio at Tel (516) 536 7375 - rigs@sunmachinery.com