1500' - 2000'+ DRILL RIGS
MAYHEW 2000 (Ref#1721R)
Trailer mounted, 58’ derrick, 4” x 35’ kelly, double drum drawworks (rebuilt 2010), drilling platform and side walkways with guard rails, 7-1/2” rotary table (rebuilt 2011), 1800’ x 3” flush joint drill pipe, (12) 30’ x 4-1/2” drill collars, front and back leveling rams, derrick lighting rams (rebuilt 2010), drive line (rebuilt 2010 with new clutch pads), 471 Detroit deck engine with 4 speed transmission (rebuilt 2011), 500 gallon deck mounted fuel tank, 50 gallon side mounted aux tank, no pulldown, block and tools included, air clutches, very good rubber.
7-1/2 x 10” Gardner Denver FXO duplex mud pump with Cummins diesel engine skid mounted (fluid end rebuilt 2010, power pistons and liners rebuilt 2010), excellent condtion
Price: $300,000
GARDNER DENVER 2000 (Ref#11047R)
Manufactured 1976, double drum drawworks, mounted on Pemco 4-axle carrier, with hydraulic leveling jacks, 64’ hydraulically raised mast with racking board with Derrick lights, 12V71 Detroit w/425HP, 12” rotary table, 4 ½” square kelly, 7 ½ x 10” mud pump on deck. PRICE: $230,000
GARDNER DENVER MAYHEW 2000 (Ref#4974N)
Gardner Denver 2000 double drum drawworks, Cabot right angle gear box, Foster breakout wrench, spinning cathead, Martin Decker weight indicator, mounted on 1975 GMC 9500 tandem axle truck with Detroit 8V71 diesel engine, Fuller 10 speed transmission, 8 hole PTO with hydraulic pump, Fuller 3TA-92 auxiliary transmission, 58’ x 75,000# hydraulically raised mast, 7-1/4 x 10 Gardner Denver FXO duplex mud pump, National J12 swivel, 3-1/2” x 37’ square kelly, Web Wilson type D rotary tongs, 7-3/4” Gardner Denver rotary table, chain pulldown, 6V71 Detroit diesel, Allison 600 torque converter mounted on deck.
36’ tandem axle low boy trailer with 1000 gallon diesel tank, 10 kw 3 phase genertor, air compressor 5 hp electric motor, (2) 85 gallon oil lubsters, (3) storage boxes, spare parts and supplies.
Casing elevators and slips
(1) doghouse 24’L x 98’W with 10 steel lockers, knowledge box and storage area
2000’ of 3-1/2” x 31’ drill pipe with 3-1/2” tool joints
(4) 5-5/8” OD x 28’ long drill collars with 4” full hole
Cleaned and painted
Price:
$275,000
PRICE REDUCED: $155,000
GARDNER DENVER 2000 (Ref#6502Ra)
Manufactured 1977, 58’ mast, mounted on CCC, 6 lines, 5 ½ x 8 GD mud pump, rebuilt 10” table, Little Giant swivel, weight indicator, 35’ x 5 ¼” Kelly Price: $205,000
FAILING 2000CF (Ref#5478N)
Manufactured 1973,
(2) 5 x 10 Gardner Denver mud pumps (one skid mouunted and one on rig), mounted
on Kenworth truck with 350 Cummins Big Cam, 18” rotary table, air clutches,
hydromatic aux brake, pipe rack, 3” swivel, cathead, 58’ hydraulically raised
mast, hydraulic breakout wrench, tongs, 4 jacks, catwalk (trailer), (11) 6”
drill collars, 1700’ of 3-1/2” x 31’ white band drill pipe – just spend $140,000
on reworking Price: $280,000 PRICE REDUCED: $260,000
FAILING 2000CF (Ref#3748N)
Double drum, mounted on tandem axle trailer, 4 hydraulic leveling jacks, hydraulic pulldown chain, 30XV King swivel, blocks, 18” rotary, 5-1/2 x 8” Gardner Denver duplex mud pump powered by Detroit 6V71 engine, air compressor, 6V71 Detroit deck engine, 30’ square kelly, hydraulically raised mast 50’, has run 40’ casing, gone over in 2008, drilled 1 well in 2008, being sold due to lack of work.
The following specifications are estimated: deck engine model, length and capacity of mast, length and diameter of kelly Price: $275,000
FAILING 2000 (Ref#9519N)
Manufactured 1974, HD2000 drawworks, 53’ stiff mast x 100,000#, Detroit Series 60 diesel engine, 18” Howard Turner rotary table, 3” Little Giant swivel, 4-1/4” hex x 35’ long kelly with kelly bushing, mounted on 8’ x 40’ custom built tandem axle trailer with deck mounted fuel tank and toolboxes, hinged steel working platform, deck mounted hydraulic system, winch, injection pump, hydraulic generator, 5 hydraulic leveling jacks, spring ride on all axles with air brakes, safety equipment, tools and spares Price: $250,000
2000’ DOUBLE DRUM TRAILER RIG (Ref#3643R)
40’ Kelly, 12” table, 55’ mast, 4 part lines, 2 catheads (1 auto) weight indicator, 3 hydraulic leveling jacks Price: $100,000
CHICAGO PNEUMATIC RT-1800 (Ref#715R)
Manufactured 1981, 850/350 air compressor, 7-1/2” x 10” Gardner Denver duplex mud pump, 52’ x 80,000# hydraulically raised mast, 10-1/2” retractable rotary table, new Detroit Series 60 diesel engine, 750 Allison transmission, mounted on Crane Carrier Price: $185,000
CHICAGO PNEUMATIC RT-1800 (Ref#828Na)
Manufactured 1978, 5-1/2 x 8 Gardner Denver mud pump hydraulic driven, 825/250 air compressor, 10” retractable rotary table, 30’ mast, 18 gpm water injection, hammer oiler, 3 lines, mounted on Crane Carrier with 400 Cummins engine, Jake brake, rebuilt chain, bearings and table, rebuilt controls and gauges, good running condition Price: $160,000 (pipe available at extra cost)
1995 INTERNATIONAL 9370 10 WHEEL WATER TRUCK (Ref#828Nb) Cat engine, 2300 gallon Flatwater Fleet tank, 200 gallon electric fuel pump, 8600# crane cattachment, radial remote horizontal boxes Price: $60,000
SPEEDSTAR SS-25-SD (Ref#4616)
Manufactured 1984, triple drum drawworks, cathead, breakout cylinder, sandreel, (2) 471T Detroit diesel 380 hp total, Gardner Denver 7-1/2 x 10” duplex mud pump, liner range 5” – 7-1/2”, weight indicator, 18” rotary table, 38’ x 5-1/4” kelly, 3” swivel, tongs with counterbalances, lighting system, 3” elevators, slips, drill collar slips, extra liners, swivel packing and parts, mounted on 2 axle trailer with 4 hydraulic leveling jacks.
250 barrel tank mounted mud system with sediment tank and electric mud lift system to shaker, extra shaker motor and screens.
100 kw, 230 volt, 3 phase skid mounted generator system,
2,150’ of 3-1/2” x 31’ drill pipe, 2 drill collars, pickup nipples, bit subs.
Catwalk, V-Door, pipe racks,
2009 Southwest support trailer, 20’ gooseneck lowboy with 7k axles, spare, storage cabinets, large vise and chain vise.
1979 Mack truck tandem axle with Maxidyne engine oilfield bed, gin poles, winch, 5th wheel and 40’ Fruehauf trailer with rolling tailboard (good condition, DOT inspected).
Price:
$700,000
PRICE REDUCED: $500,000
SPEEDSTAR SS-22 (Ref#731Nb)
Manufactured 2005,
4450 hours, 51’ x 80,000# derrick, 3 drum drawworks, mounted on 3 axle 2005 Mack
Granite truck with 427 Mack diesel engine, 7-1/2 x 10” FY-FXD duplex mud pump,
34’ hex kelly, 3” swivel, 18” retractable table, pipe spinners, breakout ram,
block/hook, kelly, kelly bushing, some pipe and tools Price:
$590,000 PRICE REDUCED: $510,000
SPEEDSTAR SS-22 (Ref#731Na)
Manufactured 1982,
3 drum drawworks, 54’ x 80,000# hydraulically raised mast, mounted on 4 axle
Crane Carrier powered by Cummins N14 diesel engine, Gardner Denver FO-FXO 7-1/4
x 10” mud pump, 10” retractable table, racking board, block/hook, kelly, kelly
bushing, currently drilling Price: $330,000 PRICE:
$245,000
SPEEDSTAR SS-22 (Ref#3369R)
Manufactured 1982, 3 drum, 5/8” lines, 5/16” x 1500’ swab/sandline, 56’ x 80,000# hydraulically raised mast, mounted on 4 axle Crane Carrier with 400 hp Cummins diesel engine, 7-1/2” x 10” Gardner Denver duplex mud pump, air clutch, Mission charge pump and pressure oiling system, (2) 256 air compressors 450 cfm/250 psi (rebuilt 10/2010 with 60 hours), 10” retractable hydrostatic 5 speed rotary table, McKissick 30 ton block rigged up on 5 lines, 60,000# casing, 4 lines on kelly, oil injection, 3” mud/air piping, Western swivel with 35’ x 4-1/2” square retractble kelly, 1,500’ of 3-1/2” x 30’ x 3-1/2 IF bottleneck drill pipe, (4) 4-3/4 collars with wrench flats, tools and bit sub, pipe float trailer, no pulldown system, could be reinstalled on brackets and sheaves on derrick, weight indicator, hydraulic tong pull set up with gauge, Rauch pipe spinner. Price: $295,000
PORTADRILL TKT PROSPECTOR (ref#8756N)
Manufactured 1983,
mounted on 1980 Kenworth C500 chassis 4-axle, 7 x 10 mud pump, air compressor,
33’ kelly, 40’ mud tank shaker, drill collar, 2050’ pipe, stabilizers, bits,
tools and accessories Price: $510,000 Price Reduced:
$380,000
PORTADRILL TKT (Ref#7369Rc)
Extended rack and racking board, 7” Portadrilll retractable table, 5-1/2 x 8 Gardner Denver mud pump mounted on rig, 650 LeRoi air compressor on rig, (5) leveing jacks, 54” mast with racking board, pulldowns and hydraulic casing tongs, safety equipment, mounted on 1980 Paystar 5000 3 axle truck.
Pipe truck: Freightliner flatbed, toolbxoes, 1,000’ of 3-1/2” flush drill pipe, (2) 6” drill collars, cross over subs, handling tools, 12” diverter with 8” flowline, numerous casing tools and equipment.
Vac truck: Peterbilt, 80 barrel with Masport vac pump and hoses
Backhoe: John Deere 410 4wd
Light tower: Ingersoll Rand
Portable Air Compressor: Ingersoll Rand 900cfm/350 psi
Package Price: $280,000
PORTADRILL TKT (Ref#1475Na)
Manufactured 1979,
500/250 LeRoi air compressor, Gardner Denver 6 x 8 mud pump, 53’ mast with
racking board, mounted on 1979 International Paystar 5000 truck, 6V92 Detroit
motor 1200 hours, reworked before being put into use. Can drill to 4500’ with
the Emsco D300 pump. Price: $200,000
PRICE REDUCED: $150,000
1987 INTERNATIONAL WATER TRUCK (Ref#1475Nd) 2800 gallon square tank, Rosewall grouter, new rubber, 400 Cummins RTO 13 tansmission - $35,000
PORTADRILL TKT PROSPECTOR (Ref#317N)
53’ mast on triaxle 1981 Kenworth truck with Detroit 6V92 engine, 5-1/2 x 8 Gardner Denver FXX mud pump, hydraulic pulldown, new 30’ kelly, 2,250’ of 2-7/8” drill pipe, cleaned, painted and reworked Price: $195,000
PORTADRILL TKT (Ref#417N)
Manufactured 1976,
PTO, mounted on International Paystar 5000 with rebuilt 350 Cummins engine, 6 x
8 Gardner Denver mud pump, 256S2 Leroi compressor, Bean water injection, 7 ½”
retractable table, 53’ hydraulically raised mast, hydraulic pulldown,
hydrostatic, breakout tongs, 4 ½” hex Kelly (fluted available) no pipe rack or
rod box Price: $245,000 PRICE REDUCED: $220,000
Pipe avail at extra cost
PORTADRILL TKT (Ref#8281N)
Manufactured 1978, Triple drum, 5-1/2” x 8” Gardner Denver duplex mud pump, LeRoi 256 S2 450/250 air compressor, 53’ x 60,000# hydraulic raised mast, Racking board, Mounted on 1978 Kenworth tandem axle truck with 8V92 Detroit diesel and PTO, 4 hydraulic leveling jacks and 2 rear screw jacks, Hydrostatic DW, Water injection, 8” retractable rotary table, Price: $145,000
Also available at extra cost: 2000’ of 3-1/2” x 20’ drill pipe and additional rebuilt compressor
PORTADRILL 10 TKT (Ref#15418)
Manufactured 1976, depth capacity 1800’, mounted on 1975 International 5000 truck, (1) LeRoi 253-S2 (750/250) air compressor and (1) LeRoi 256-S2 (500/250) air compressor on gooseneck trailer: total 1250 cfm/250 psi, 6V92 Detroit engine (rebuilt, 300 hours), 400 hp PTO, pipe box, 5/8” cable, rated at 40,000#, Bean water injection, 3 leveling jacks, 7-1/2” Gardner Denver retractable rotary table, 1000’ of 4-1/2” x 15’ pipe, fully equipped, stabilizers, tools, hammers
Tandem axle trailer mounted mud handling system: Gaso 5 x 10 duplex mud pump produces 320 gpm @ 330 psi, (3) desanders, hydraulic powered pickup pump and a 1000 gallon tank, (2) 6V71 Detroit diesels with (2) hydraulic pumps to power shakerand the mud pickup pump
Price:
$175,000
PRICE REDUCED: $125,000
PORTADRILL 10 TKT (Ref#1236N)
Manufactured 1974, rebuilt, low hours, 5-1/2 x 8 Gardner Denver chain driven mud pump (rebuilt), 256 LeRoi air compressor (rebuilt), 7-1/2” retractable table, mechanical clutches, pulldown, 4-1/2” x 23’ kelly (mast is set up for 30’ kelly), mounted on 1999 Kenworth truck with 440 hp Cat engine, PTO, pipe spinner, breakout tongs, water injection pump, 3 hydraluc leveling jacks, good condition, rebuilt hydrostate, chain cases and rotary table, currently drilling Price: $370,000
Pipe available at extra cost.
SUN MACHINERY CORP
Telephone: (516) 536 7375 Fax: (516) 536 7317
email: rigs@sunmachinery.us